A power plant condenser (heat exchanger) trans-fers 100 MW from steam running in a pipe to sea-water being pumped through the heat exchanger.The wall separating the flows is 4 mm of steel,with k = 15 W/m K, and it has 7°C differencebetween the two fluids. Find the required area ofthe heat exchanger.

Answered: Image /qna-images/answer/ac3e6bef-37cc-4993-88b0-ab27365d6d0c.jpg

power plant condenser (heat exchanger) tran ers 100 MW from steam running in a pipe to se vater being pumped through the heat exchang The wall separating the flows is 4 mm of ste vith k = 15 W/m K, and it has 7°C differen etween the two fluids. Find the required area he heat exchanger.

power plant condenser (heat exchanger) tran ers 100 MW from steam running in a pipe to se vater being pumped through the heat exchang The wall separating the flows is 4 mm of ste vith k = 15 W/m K, and it has 7°C differen etween the two fluids. Find the required area he heat exchanger.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Pnoblem # 20. Ugi ng hot water C reow rate = 8.28 m³ Ih , mlet tenpenature= 155,39 °F), Ca Hy O or 221°F, outhet temperature ethanol is being he ated rom 98. 6 °F C rade = 12-6 m3 /h 98. 6 °F ( Hlow rade = 12-6 through a shell and fube 1-2 pass heat exchanger. heat ņ CoHG O = 1.63 B tu llb oF capacity %3D heat traws fer coef ficie nt Uo = 363, 99 8tu h ft"F over all %3D Solve for for heat exchanger area recquired outlet temperature if heau trans fer raste of ethanol = 5.810 Watts %3D C) , , log mean tmperatue this heat exehanger. me an temperature diffe rence difference of corecti on factor
The clean U for an exchanger is 770 BTU/(hr 0 F ft2). Its tube area is 550 ft2. After operating for several months, it is heating water from 40 0F to 150 0F at a flow rate of 200 GPM with a heating fluid on the shell entering at 300 0F and exiting at 170 0 F. Has the overall U decreased significantly? how many 1.0 inch diameter, 20 ft long tubes would it take to equal the 550 ft2 area?
I need the answer as soon as possible
I am in a hurry, I need the answer as soon as possible, please help.
A shell and tube heat exchanger operates with two shell passes and four tube passes . The shell fluid is ethylene glycol which is cooled from 140c to 80c & ( Cp = 2742). Watue flows in the tubes, entering at 35c and leaving at 85c. The overall HTC for this arrangement is 850 w /m2k. Calculate the flow rate of water required and the %3D area of the the H. E. ?
Solve it completely Don't do it partially
A heat exchanger is a system used to transfer heat between two or more fluids. Explain industrial application of different types of heat exchanger and also explain LMTD method counter & parallel flow arrangement.
In industrial processes, heat exchangers are widely used to transfer heat from one process to another. There are a wide range of heat exchanger problems that may cause poor performance. Below is a picture of one type of heat exchanger. Study it and answer the following questions: Fluid 2 in Fluid 1 out Fluid 1 in Fluid 2 out i) Determine the type of flow in this heat exchanger. How the efficiency of the heat exchanger changes if the Does operator reverses the flow arrangement of fluid? If a process engineer wants to improve the efficiency of this heat exchanger, what ii) do you recommend to increase the efficiency? B III
For the given temperature profile diagram for a heat exchanger, which of the following equation is coIrect, ping x Boding fhed Inlet Outiet a. mhyg = m.Cpc(Tco – Tei) b. m.Cpn(Tn - Tho) = m.Cpc(Ta – Teco) m,C,(Th: - Tho) = m.Cpc(Tco – Te) m,Cpn (Thi - Tho) = m.hr,
heat trawafer coefficient Problem #21. Cz Moo Cethanal) i (flow pute - 12.4 mh) through a being 98.6°F heate d from m2/h) though a 2-4 Shell and tube heat exchong er whing hot water (flow pate= 8-29 m³ /h, 155.39 °F). inlet temperature- 221 F, outlet mperature= awerage heat capaci ty of CaHeO - li63 Btu J lb'F = 5.8 * 105 Watts = 363. 99 Btu|hft°F heat trans fer rate ethanol %3D overall heat trawafer %3D Jelve for: a. comeetion factor 6 (Ao) mean temperature differe nce outaide nur face are a veguired
(3) In a counter flow heat exchanger if AT = AT, show that AT = AT = AT. AT is the log mean temperature difference and AT, and AT, is the temperature difference at inlet and outlet respectively.
PLZ I want full answer with all solution steps A heat exchanger is to be designed to heat 32/68 mixture of ethylene glycol and water from 24 °C to 55 °C by a hot water stream from 79 °C to 42 °C. Flow rate of cold stream is 20 kg/s. Inlet pressure for both stream is 50 psi and the maximum pressure drop of 10 psi for cold stream and 8 psi for hot water are permissible. Report valid assumptions made for the design and give required justification. Estimate i) Heat Transfer, Corrected LMTD, ii) Tube bundle diameter (Using TEMA standards and Codes) and Tube cross sectional area iii) Heat transfer coefficient iv) Overall heat transfer coefficient v) Pressure Drop (Shell side & Tube Side) note: Assume any values for the missing data