mplify the block diagram shown in following figure and obtain the closed-loop ansfer function C(s)/R(s).

Q: (b) Find the Q-point (VcF,Ic) if given Boc =150 for the BJT circuit shown in Figure Q3(b). Vcc +10V…

A: In this question,  We need to determine the Q point of the BJT.  If dc current gain = 150 Assume…

Q: c. When analyzing op-amp circuits, we introduced the virtual ground concept. Sketch a simple op-amp…

A: c)  To explain virtual ground concept in opamap circuits

Q: M14 M15 M11 M3 M7 M12 M10 M16 M17 No CM vit d M1 v2 HH M2 M18 M19 RL M13 MB RB M4 M5 MB VR VSS…

A: Gate current for the Nmos and Pmos  is equal to 0A. From the above point , we can conclude that the…

Q: -5V 47K 20K V3

A:

Q: Project # 3 (Use a FET op-amp) You’ve been working with an implementation team to build the…

A: Given :Duty cycle=50%It consists of four different frequenciesLet frequencies 2kHz, 4kHz, 6kHz and…

Q: The output of the op-amp comparator is a a. rectangular waveform O b. sawtooth waveform O . triangle…

A:

Q: Connect a thermistor (Resistance=500 – 1% per °C ) in a bridge (power supply =8V) with an…

A: Given:- Rt=500ohmα=1% per°cV=8voutput of inverting amplifier=4v at 30°t= final temperature=30°

Q: III Determine the output voltage of the ideal op-amp differentiator in Figure below for the sv-…

A:

Q: The waveforms shown below are V₁ and Vo of a schmitt trigger circuit. From these waveforms the…

A: The Given waveforms the values of the two comparison voltage V1 and V2 To Schmitt trigger circuit Vi…

Q: Q3. Draw the output voltage Vout waveform of the op-amp circuit shown in Figure Q3. The supply…

A: The solution can be achieved as follows.

Q: R it) Vout in

A: Given circuit FIRST ORDER RC FILTER

Q: Q1/(b) Calculate cutoff frequency high for the cct. below at R1=R2= 10Kn and C1=C2=D0.002 uF * in in…

A:

Q: Identify an industrial application where OPAMP is required and design circuit for the same…

A: An OPAMP(operational amplifier) is an integrated electronic circuit that is used to amplify weak…

Q: In a stair step A/D converter, clock frequency is 1 MHz, threshold voltage is (0.1 V). The full…

A:

Q: 2. Determine the transfer function of the circuit.

A:

Q: Draw the circuit diagram of a differential amplifier using one op amp and resistances as needed.…

A: The differential amplifier has two inputs attached to two different terminals of Op-amp. The…

Q: c. The filter is a device that allows passing the dc component of the load and blocks the ac…

A: A filter circuit is an electronic device which blocks the ac component present in the rectified…

Q: The difference between Vcs and vGs is Select one: a. The first is ac and the second is de b. The…

A: MOSFET (Metal oxide Semiconductor Field Effect Transistor ) is Field effect transistor having 4…

Q: Consider the following step up converter with a resistive load of value R-5 ohms. It is supplied by…

A: Consider the following step up converter with a resistive load of value R=5 ohms. It is supplied by…

Q: What is a Differentiator circuit ? Draw and find the transfer function of OPAMP based Differentiator…

A:

Q: OL Simplify the block diagram shown in Figure(1) and obtain the closed- loop transfer function C(s)…

A: Given block diagram

Q: The if the input to a Differentiator op-amp is a DC signal then the magnitude of the output will…

A:

Q: Please check

A:

Q: Consider the following step up converter with a resistive load of value R-5 ohms. It is supplied by…

A: Given data: -F=5 kHzR=5 ΩVs= 200 VD=0.5L=10 mHFind: -The maximum current in mode  2.

Q: please solve step by step. please show all properties of op-amp.

A:

Q: Draw the schematic diagram of the series-positive limiter and the series-negative limiter;…

A: A series positive limiter clipper circuit is a type of electronic circuit that limits or clips the…

Q: Discuss comparator with its voltage transfer charcateristic.

A: Operational Amplifier is direct coupled high gain amplifier. The  OP-AMP is multi terminal device.…

Q: b) You are required to design an integrated circuit voltage regulator of LM317 circuit that produce…

A: Given :Vin=18 VVout=12 VIReg=2 mA

Q: The buck converter with resistive load has the input voltage of 30[V], the output voltage of 20 [V]…

A:

Q: With an op amp design a square wave oscillator at ± 3 volts with a frequency at 20 kHz. Draw the…

A: According to the question, we need to design a square wave oscillator by using OP-AMP with the…

Q: (c) (i) When 10100 is input to a 5-bit digital-to-analog converter, the output current is 10 mA.…

A: Since you have asked multiple questions , we will solve the first question for you . If you want any…

Q: Using the basic configurations of OpAmps, as well as those of integrators and spinners, implement…

A:

Nodal Analysis

In the analysis of any electric circuit, nodal analysis is the method of determining the potential difference or voltage between different nodes in an electric circuit. A node is a point where two or more branches connect each other. In the nodal analysis, the voltages are determined in the terms of branch currents. The nodal analysis is also known as the node voltage method or branch current method. The nodal analysis method is one of the several applications of Kirchhoff's Current Law (KCL).