Please round to the nearest One (i.e., 1). PLEASE DO NOT USE COMMA(S) ON YOUR ANSWER!!! Moist unit weight of soil, gamma = 130 pcf Saturated unit weight of soil, gammasat = 140 pcf Cohesion of soil, c = 0 psf The factor of safety, FS = 4 The internal friction angle of soil is 35 degrees B = 3 ft, D₁ = 4 ft, h = 2 ft A square footing is shown below. Determine the followings: Df 67 MAA P A Qali TAF B 1. Ultimate bearing capacity, qu = 2. Allowable bearing capacity, qa = P Unit weight of soil = y Groundwater table Ysat psf $' psf

Please round to the nearest One (i.e., 1). PLEASE DO NOT USE COMMA(S) ON YOUR ANSWER!!! Moist unit weight of soil, gamma = 130 pcf Saturated unit weight of soil, gammasat = 140 pcf Cohesion of soil, c = 0 psf The factor of safety, FS = 4 The internal friction angle of soil is 35 degrees B = 3 ft, D₁ = 4 ft, h = 2 ft A square footing is shown below. Determine the followings: Df 67 MAA P A Qali TAF B 1. Ultimate bearing capacity, qu = 2. Allowable bearing capacity, qa = P Unit weight of soil = y Groundwater table Ysat psf $' psf

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

In the hatched region in the diagram, water is flowing through saturated earth. Calculate the total heads and elevation pressure at places A, B, and C. Calculate the water flow rate through the soil if the coefficient of permeability of the soil in the hatched region is 5 cm/sec and the cross sectional area of the soil sample is 15m2.
Solve part 1 only
Please help
8. Estimate the settlement of the center of the tank, shown in the sketch, due to consolidation of the 20-ft layer of clay. 80'diam. -Oil tank; 500 lb/sq ft 30' fine sand; 125 lb/cu ft 20'clay; qu = 1.3 tons/sq ft W = 54 % Wp = 26% W = 44% Isat = /15 lb /cu ft %3D Rock %3D %3D
I’m stuck please help me! I will leave thumbs up! Show work so i can understand please!
Please answer situation 7
KOOHAN ERSITES MSKÜ-LMS 3\ A soil profile is given below. 3m thick dry clay is underlain by 4m thick sand. At the bottom 6m thick saturated clay layer is present which is underlain by impervious and massive bedrock. planmad Related data are provided in the figure. (No capillary action) and (A, B and C points are located in the middle of the layers Duzerinden tienmis Match the related data: oruyu tie surface 3m Dry clay, va:16KN/m Sand, yeni19kN/m? 4m Yan 22kN/m Saturated clay, Yary 20kN/m 6m Impervious bedrock Effective vertical stress at point C in kPa If a surcharge (100KPA additional uniform load) is applied to the surface, what is thệ excess pore water pressure at point Cimmediate construction (in kPa)? 140 95 Effective vertical stress at point B (in kPa) If a surcharge (100kPa additional uniform load) is applied to the surface what is the excess pore waten pressure in the sand after the construction (in kPa)? Total vertical stress at point C in kPa Pore water pressure at point C…
ASAP-Topic Soil Mechanics....0-4
2. A cylinder was carefully pushed into the soil without compressing or disturbing the soil. The cross- sectional area of the cylinder was 19.6 cm?. The length of the column of soil within the cylinder was 7 cm. The weight of the soil within the cylinder was 185 g when it was dried. The weight of the soil before oven drying was 225 g. Determine Pw, As, and Py,
Soil sample has a saturated unit wt. of 20kN/m3 and internal friction angle of 30°. Compute the slope angle for a factor of safety of 1.5. Use unit wt. of water as 9.81kN/m3.
Geotechnical Engineering
1) Properties of soil and concrete Osal 4m 9 = 30° Cohesion =0 Coefficient of base friction = 0.50 Soil's ultimate bearing copacity= V25 k 2m %3D 12 0.0 use Rankine's theovy Considering no evosion and future excavaton would happen in the Soil a) Detemine the location of the active force from the boase. 67 Determine the total normal force reachion of soil at the bose. c) Determine FS SIDING. d) Determine FSarturning o e) Determine PSpcoing. C-