Please provide two examples: (1) an example of a design scenario that would be appropriate for the using theLewis form factor for gear design, and (2) another design scenario that would be more appropriate to theAGMA method of gear design.

The Lewis Bending equation : σ=MI/c=6WtlFt2 Take a example for the gear design on Lewis equation:…

Answered: Please provide two examples: (1) an…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

please send handwritten solution Q4 part b
Choose the correct option
A portion of the shaft where a gear is to be mounted has a diameter of 1.5in. The gear transmits 3000 lb.in of torque. The shaft is made of SAE 1040 OQT400 steel, the gear is made of SAE 8650 OQT1300 steel, and the key is made of SAE 1045. The minimum required length for this key is most likely: 0.5in 2.5in 3.0in 1.0in 1.5in
The output shaft diameter is typically larger than the input shaft diameter on worm drive gearboxes. Explain why
please send handwritten solution Q4 part c
please send handwritten solution Q4 part a
Why toothed gears are preferred over Rope, Belt, and chain drive? Also specify the application for each drive system. Answer with word clearly please
You have been tasked with designing a set of gears made from a material with a Brinell hardness (Hg) of 201 MPa. Previously your company has produced gears with a commercially polished surface finish, but your boss is interested in how much the bending strength would be decreased if a machined surface was used instead, with all other factors kept constant. Considering the surface factor figure and the AGMA equation for bending strength presented below, approximately what percentage decrease in bending strength (S,) would we expect to see changing from a commercial polished finish to machined surfaces? Hardness (Hp) 120 160 200 240 280 320 360 400 440 480 520 1.0 `Mirror-polished 0.9 Fine-ground or commercially polished 0.8 - Machined or cold-drawn 0.7 0.6 0.5 Hot-rolled 0.4 0.3 As forged 0.2 Corroded in tap water 0.1 Corroded in salt water 60 80 100 120 140 160 180 200 220 240 260 Tensile strength S, (ksi) St Sn = S'nCskrk¢kms O 28% O 20% O 23% O 7% Surface factor C,
PLS ANS QUICKLY
A shaft where a hub is mounted has 2 in diameter, transmitting 20 hp power at 750 rpm. Design a square key made of steel for factor of safety (n) =3. Use preferred sizes.
State the design specifications for pinion(665M13)and gear(817M40) considering the following design factors : 1.Functionality 2.Stress
What is benefits of cycloidal gear?

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

Please provide two examples: (1) an example of a design scenario that would be appropriate for the using the Lewis form factor for gear design, and (2) another design scenario that would be more appropriate to the AGMA method of gear design.