As a senior automotive engineer, you are asked to design a transmission featuring 2-speed forward ratios and 1 reverse gear that can handle an engine with the maximum torque of 50 Nm (at 3500 RPM) and the maximum speed of 5000 RPM (torque of 35 Nm). The transmission must be able to provide: - the maximum output torque of at least 120 Nm, - the maximum output speed of at least 6000 RPM.

As a senior automotive engineer, you are asked to design a transmission featuring 2-speed forward ratios and 1 reverse gear that can handle an engine with the maximum torque of 50 Nm (at 3500 RPM) and the maximum speed of 5000 RPM (torque of 35 Nm). The transmission must be able to provide: - the maximum output torque of at least 120 Nm, - the maximum output speed of at least 6000 RPM.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q12:- Two involute gears of 20° pressure angle are in mesh. The number of teeth on pinion is 20 and the gear ratio is 2.0. The module= 5 mm and the pitch line speed is 120 cm/sec and assuming the addendum as standard and equal to one Find:- (a) the angle turned through by when one pair of teeth is in mesh and (b) the maximum sliding velocity. module.
Q5:- The particulars of a pair of spur gear are:- (a) gear ratio=(1/10), (b) center distance3D 660 mm approximately, (c) power transmitted%3D 500 kW, (d) speed of the pinion= 1800 rpm, (e) teeth are of involute form with pressure angle= 22.5°, (f) the addendum= 1 module and (g) the permissible normal force between teeth is 200 N/mm of gear width. Find :- (a) the nearest standard module if no interference to occur, (b) the number of teeth on each wheel and (c) the necessary width of pinion and gear.
An electric motor develops 6 HP at 3000 rpm. An 18 tooth gear is fitted to its shaft to drive a gear on an output shaft. How many teeth would be needed on this output gear if an output torque of 100 Nm is required? Answer: Ti vious page Next page https://learnonline.gmit.ie/mod/quiz/attempt.php?attempt-126637&cmid-1429658page-3# CHao Search for anything FI1 F10 F8 F9
A planetary gear train has Nsun = 30, Nplanet = 60, a module of 3 mm, a 20o pressure angle and is to transmit 5 kW. What torque can be delivered by the armature if the sun is driven at 1500 rpm and the ring is stationary?
Please help
(a) Two involute gears of _pressure angle are in mesh. The number of teeth on pinion is 20 and the gear ratio is_. If the pitch expressed in module is 5 mm and the pitch line speed is_m/s, assuming addendum as standard and equal to one module, find : 1. The angle turned through by pinion when one pair of teeth is in mesh 2. The maximum velocity of sliding. D=30 G= 2 V=1.4m/sec
Pls explain to step by step and i will rate your answer immediately. Thanks
73 all a O ... 2 docs.google.com/forms/d Un the piion is more inan ihat of ine gear. Q5:- The minimum number of pinion teeth in the rack and pinion arrangement of standard gear and pressure angle 20 degree is:- * none of these 13 18 16 15 Q1:- The radius of the dedundum circle of a gear is equal to:- The pitch circle radius divided by the cosine of the pressure angle.
please help me calculate the velocity ratio
73 ll a O ... simple 23.5% epicyclic none of these 76.5% Q5:- The purpose of the idler gear in a gear train is:- 17 responses To connect gears where a large center distance is available. 82.4% None of these. To control the directional relationship between the first 17.6% and last gears. This content is neither created nor endorsed by Google. Report Abuse - Terms of Service - Privacy Policy Google Forms
How are Gear ratio and Speed ratio related? Are they equal to each other?