Please do 10 and 11. No explanation needed

Q: You wish to turn on two LEDs in the middle of the display, so the first thing you will do is set AL…

A: As per our policy, i have attempted 1 question  Given to turn on two LEDs in the middle of the…

Q: Convert the decimal NUMBER 19711.654785156 to octal number showing the steps (Note : The problem…

A:

Q: Differentiate between MCB and kit kat fuse

A: MCB : MCB stands for miniature circuit breaker it is a electrical device in such way that it…

Q: The -------parameters may not reflect the actual operating conditions but simply provide an…

A: 1. The advantages of the re model are that the variables are determined by the real operating…

Q: mostly don't know how to do question (d) and (e)

A:

Q: Determine the following: Ic, VF , VR , R1

A: BJT (bipolar junction transistor) A transistor having a three terminal made up of semiconductor…

Q: struction is executed two data bytes from HL registers that were previously stored on the stack are…

A: In this question, we have to explain about pop instruction and flags..

Q: When the load of a voltage multiplier is too small, __." Choices: the output voltage is unaffected…

A: Voltage multiplier is the circuit which is used to give high dc value of voltage at the output…

Q: The figure below shows a loạding truck in a cement factory. The truck has three wheels, front wheel…

A: According to the question, we need to design a control circuit by using a multiplexer that operates…

Q: Cần be driven by a single digital 1C output is a characteristic called a) low power dissipation. c)…

A: 2. The number of parallel loads that can be driven by the single digital IC output is a…

Q: can i series my led chip even though i don't put any fuse. Is it safe?

A: Most of circuit does not contain fuse for LED Chip Reason behind not putting fuse for LED Chip is…

Q: Design a control of traffic lights application(PLC) . In this application,   the lights control…

A:

Q: A speedometer is connected in an automobile system to measure the speed. The meter reads 120.8 rpm…

A: In this question we need to choose a correct option

Q: Convert the decimal number 694 to BCD. Kindly put subscript in answer.

A: Brief description : In digital electronics we have different type of number systems such as,  Binary…

Q: need the answer as soon as possible

A:

Q: Draw the state diagram to detect sequence 10110. Also write its verilog code

A: The state diagram is visual representation of the sequence. It shows the internal states and…

Q: 2. Convert (0101), to decimal. 3. Convert (0010), to decimal.

A: for 2 the given number is 0101 for the 3  the given number is 0010

Q: Create a sequence detector that detects the sequence 1001 or 0110 by using Verilog Code. Construct…

A: Detects the sequence 1001 or 0110 by using Verilog code.

Q: Explain the operation of squelch circuit

A:

Q: Q2)  The certain operational amplifier has the following data sheet specifications: IOS= 0.80 µA and…

A:

Q: Q1: Convert (10AB2), to octal number? p2: Perform (0110 1000 0010)aco + (0101 0110 0111)aco

A: Bartleby has policy to solve only first question and incase if it has subparts then solve only first…

Q: How can random error be reduced? a.Using a more accurate instrument. b.Change the measuring…

A: A random error is also called unsystematic error due to unexpected and unpredictable causes and very…

Q: used a 10KHz frequency PWM signal (default). The FTM0 timer was driven by a 60MHz bus clock. Is it…

A: According to the question, Used a 10KHz frequency PWM signal (default). The FTM0 timer was driven by…

Q: QUESTION 9 The output Lot Full Light will be energized when the accumulated count is: Ladder logic…

A: Given:

Q: The registers are involves in Indirect Cycle are: MAR, MBR O MAR, MBR, IR MAR, MBR, Control unit.…

A: After the fetch cycle is completed, the source operands are fetched and the indirect cycle occurs…

Q: Perform the following subtraction using 1’s and 2’s complement method (Show step by step process)…

A: (i) (11010)2 – (10000)2

Q: Q2 The following reading were recorded for voltage measurement 10.1. 9.7. 10.2, 9.6 9.7, 10.1, 9.6,…

A:

Q: When the pinch-off voltage is exceeded, ID will ____ as VDD increases.   a. double   b.…

A:

Q: How was 0.1 found in the initial equation?

A: It is given that: RD=33 kΩRs=10 kΩRG=1 MΩVDD=15 V

Q: 00010101 b) Ob00110100 & 0b10010100 = 0b c) Obl1010010 ^ Ob10010100 = 0b %3! + 10010110

A:

Q: Draw the block diagram and describe the principle of operation of the UPS type inline-interactive

A: When power is lost, a line-interactive UPS keeps the inverter in line and changes the battery's DC…

Q: 2) Quantization noise can be reduced by. * Decreasing the number of levels. Squaring the number of…

A: In this question , we will write how quantization noise can be reduced....

Q: Explain the purpose of the switch debouncer and how it functions?

A: Switch debouncer: Mechanical switches are a typical component in manual control circuits in both…

Q: I opened a broken Coin Pusher Arcade game to fix, and I saw a burned IC. Between Microprocessor and…

A: An arcade game is a game machine which usually found in public places like malls, restaurants and…

Q: Speed control of slipring Induction Motor. MCB Instruction SN Ammeter WattMeter Speed 1 2.6 2 2.9 3…

A: Induction motor- The induction motor is define as the AC operated electric motor. In which the…

Q: Q. No. 7: Determine the output of the following instructions and set/reset the values of the status…

A:

Q: What does the DC NULL actually measures?

A: The DC null detector is a current galvanometer whose deviation is accompanied by uneven emf. It is…

Thermistors

A thermistor is a special type of resistor whose resistance is more temperature-dependent than standard resistors.  The resistance of the thermistor decreases with increasing temperature. This is the basic principle of thermistors. This allows the thermistor circuit to detect very small temperature changes that cannot be observed with the Resistance temperature detectors (RTDs) or the thermocouples. Since the resistance of a thermistor is temperature dependent, it can be connected to an electrical circuit to measure body temperature. This high sensitivity to temperature changes makes thermistors very useful for accurately controlling and calibrating temperature measurements. In general, resistance increases with increasing temperature in most metals, but thermistors react negatively.