Please help to solve the problem below. Will upvote to the answer. Thank you (Place the origin at point A.) Let a=3.25 m, b=4.25 m, Pg = 30KN, and Pc = 100KN.PsPcCDetermine the shear force acting at each of the following locations:(a) x = 2 m(b) x = 4 m(c) x = 8 mNote that x = 0 at support A.|

Answered: Image /qna-images/answer/8b8ed2d4-a444-4709-887e-dfbb77e6831e.jpg

(Place the origin at point A.) Let a=3.25 m, b=4.25 m, P3 = 30KN, and Pc = 100KN. Pc Determine the shear force acting at each of the following locations: (a) x = 2 m (b) x = 4 m (c) x = 8 m Note that x =0 at support A.

(Place the origin at point A.) Let a=3.25 m, b=4.25 m, P3 = 30KN, and Pc = 100KN. Pc Determine the shear force acting at each of the following locations: (a) x = 2 m (b) x = 4 m (c) x = 8 m Note that x =0 at support A.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

AC and BC have the same dimensions (a square cross section of 25 mm on each side)
%3D The truss structure (all members have the same area) carry the loading shown (P = 150 kN) Determine the minimum thickness t (in mm) of the steel member considering allowable vertical displacement of C to be 12mm. Use E=200 GPa. Use Virtual Work Method to solve the problem. t E D = 200mm 3m C PV 4m 4m B
A horizontal beam is supported by an inclined strut and carries a load of 15 kN at joint AD CBD in the figure. The strut, which consists of two bars each of thickness 40 mm, is connected tothe beam by a rivet passing through the three bars meeting at joint. The allowable shear Cstress and bearing stress are all, z =60 MPa and =120 MPa, respectively.a) Determine the required diameter of the rivet at the hinge that carries safely by the given Csystem.b) If the diameter rivet used on the support is 20 mm check whether this rivet diameter is Asufficient for the given system.
Solve the problem using Moment -Area Method Problem II. The midpoint B of the steel cantilever beam ABC is supported by a vertical aluminum rod. Find the maximum allowable value of the applied force P if the stress in the rod is not to exceed 120 MPa. Use Est = 200 GPa, I = 50 x 10 mm¹ for the beam, Eal = 70 GPa, and A = 42 mm² for the rod. 5 m H B |--2--|- m -Aluminum -Steel 2 m с
A simply supported wood beam that is 12.9 m long carries a 30 kN concentrated load at B. The cross-sectional dimensions of the beam are b = 150 mm, d = 380 mm, a = 100 mm, and c = 35 mm. Section a–a is located at x = 2.2 m from B. (a) At section a–a, determine the magnitude of the shear stress in the beam at point H. (b) At section a–a, determine the magnitude of the shear stress in the beam at point K. (c) Determine the maximum horizontal shear stress that occurs in the beam at any location within the entire span. (d) Determine the maximum tensile bending stress that occurs in the beam at any location within the entire length.
A simply supported wood beam that is 12.9 m long carries a 30 kN concentrated load at B. The cross-sectional dimensions of the beam are b = 150 mm, d = 380 mm, a = 100 mm, and c = 35 mm. Section a–a is located at x = 2.2 m from B. (a) At section a–a, determine the magnitude of the shear stress in the beam at point H. (b) At section a–a, determine the magnitude of the shear stress in the beam at point K. (c) Determine the maximum horizontal shear stress that occurs in the beam at any location within the entire span. (d) Determine the maximum tensile bending stress that occurs in the beam at any location within the entire length.
A simply supported wood beam that is 4.2 m long carries a 49 kN concentrated load at B. The cross-sectional dimensions of the beam are b = 130 mm, d = 420 mm, a = 65 mm, and c = 40 mm. Section a–a is located at x = 0.7 m from B.(a) At section a–a, determine the magnitude of the shear stress in the beam at point H.(b) At section a–a, determine the magnitude of the shear stress in the beam at point K.(c) Determine the maximum horizontal shear stress that occurs in the beam at any location within the entire span.(d) Determine the maximum tensile bending stress that occurs in the beam at any location within the entire length.
A simply supported wood beam that is 4.2 m long carries a 49 kN concentrated load at B. The cross-sectional dimensions of the beam are b = 130 mm, d = 420 mm, a = 65 mm, and c = 40 mm. Section a – a is located at x = 0.7 m from B. (a) At section a – a, determine the magnitude of the shear stress in the beam at point H. (b) At section a – a, determine the magnitude of the shear stress in the beam at point K. (c) Determine the maximum horizontal shear stress that occurs in the beam at any location within the entire span. (d) Determine the maximum tensile bending stress that occurs in the beam at any location within the entire length
A frame and a loading are shown. Note that a = 90° -300 mm- B 200 mm D 175 mm A 400 mm 200 mm Determine the internal forces at point Jwhen P = 1.7 kN. The axial force is 5.143 kN The shear force is 1.5 O kN The bending moment is 1.4786 kN-m
B | 0.75 m 2.07m The rigid bar AB of negligible weight is supported by a pin at 0. When the two steel rods are attached to the ends of the bar, there is a gap A=4.3 mm between the lower end of the left rod and its pin support at C. Compute the stresses in the left and right rod after the lower end of the left rod is attached to the support. The cross-sectional areas are 305 sq.mm for rod AC and 257 sq.mm for rod BD. Use E=200 GPa for steel. AQ 1.53 m
A simply supported wood beam that is 9.0 m long carries a 30 kN concentrated load at B. The cross-sectional dimensions of the beam are b = 140 mm, d = 420 mm, a = 105 mm, and c = 20 mm. Section a–a is located at x = 1.5 m from B.(a) At section a–a, determine the magnitude of the shear stress in the beam at point H.(b) At section a–a, determine the magnitude of the shear stress in the beam at point K.(c) Determine the maximum horizontal shear stress that occurs in the beam at any location within the entire span.(d) Determine the maximum tensile bending stress that occurs in the beam at any location within the entire length.
Solve with Free body diagram