Pi= 1200 KN P = 1200KN %3D +3m Find the location of the point of inflection from the left end of the footing

Q: Solve for the deflection at midspan using Area Moment Method.  Please provide clear and complete…

A: To determine deflection at the centre of the beam

Q: 2) Given the cross sectional area below. The horizontal neutral axis is 129.0mm from reference…

A: Shear Stress Distribution :  We know that Shear stress at any section, τ = VAyINAb Given, Distance…

Q: Can you please show how to answer theta b up until to deflection in c

A:

Q: Determine the bar force member CD. All interior angles are 60 degrees. 1.5 kN 3 KN ... 2 kN F 1.5 m…

A:

Q: 4 kN/m 36 kN-m A B C E = 200 GPa ΕΙ 2EI AB = 10 mm- I = 150x106 mm² 4 m * 5 m Draw SFD, BMD,…

A: Step 1: Calculate the Reactions at the SupportsDetermine the vertical reactions at points B and…

Q: Slope at point A and deflection at midspan. 8 kN/m AREKIN INI 3m А 7m bod B

A: Given: A simply supported beam with loading  Required: Slope at A deflection at midspan

Q: Determine the shear (in kN) In member AB using Portal Method. Input the magnitude only. P=50KN B C…

A: Given data in question  Span member length  Point load Portal method To find out  Shear force in…

Q: Q.2 A simply supported reinforced concrete beam has a design span of 8 m with effective depth of 425…

A: The first step in designing the beam reinforcement is to calculate the ultimate load. The ultimate…

Q: Find R1 and R2

A: Introduction : The given beam is loaded with three load . The loads are moment , Uniformly…

Q: Identify each of the trusses in Figure Q5(a) to Q5(d) as a determinate or statically indeterminate…

A:

Q: 2) Given the cross sectional area below. The horizontal neutral axis is 129.0mm from reference…

A:

Q: The deflection and slope at C will be (take El = 12000 kNm²) 24 kN Im 60 kNm 1 m O

A: The problem involves finding the slope and displacement at a given point in a simply supported beam.…

Q: The simply supported beam shown has a 300N concentrated load located 2.0m, from the left support.…

A: To determine the maximum displacement and the maximum slope of the angle.   Given, Modulus of…

Q: 3. DETERMINE THE SLOPE BETWEEN THE SUPPORTS. 1S0 KN 15 KN|m E= 70 GPa FIG.2 I- 630 (10)° mm 5m 5m 4m

A:

Q: Design the torsional and shear reinforcement for the beam as shown in the figure. The resulting L…

A: Given data- Span L = 14 m Z = 2.4 m h = 800 mm Width b = 400 mm Thickness t = 150 mm d = 735 mm fc =…

Q: Use the virtual work method to determine the horizontal and vertical components of the deflection at…

A:

Q: Find redundant REy. All bar areas equal. (Ans: REy = 45.44 k) 60 k BY 30 k E D 60 k 30 ft - K30 ft -

A:

Q: Wo B Wo B

A:

Q: From the beam shown. Let P = 30 kN, Q = 2 kN/m, L =6m and EI = 200MNm^2 Determine the following;…

A: Given data:

Q: Smaller angle: Larger angle: s = 20 ft Determine the two possible angles so that the water strikes…

A: This question is related to the Engineering Mechanics.

Q: 3. Calculate the slope at C, location and value of the maximum deflection, and deflection at B. 50…

A:

Q: Replace the parallel force system acting on the plate by a resultant force and specify its location…

A: to find resultant and its location on x-z plane

Q: 2) Given the cross sectional area below. The horizontal neutral axis is 129.0mm from reference…

A: Solution;

Q: 67 kN -6.5 m = 200 GPa I = 315 × 106 mm* E 41

A:

Q: Using the slope-deflection method, draw the bending moment diagram. 3m 3A 4. Moment @ A -49.51kN-m…

A:

Q: The simple beam 120mm x 420 mm cross section has E= 9.50 GPA Determine the vertical movement of…

A: Reactions: Shear Diagram: Bending Moment Diagram:

Q: 4.) Find the centroid of the area of a trapezoid that has two equal slanting sides, a 12 in base and…

A:

Q: 2) Given the cross sectional area below. The horizontal neutral axis is 129.0mm from reference…

A: Solution:

Q: Determine the angle θ between the pipe segments BA and BC.

A: First, we draw the free body diagram:-

Q: 3. Determine the angle 0 for the connecting member A to the plate so that the resultant force of FA…

A:

Q: Determine the slope at B and the deflection at C CET313-SP-013. E = 200 of the beam in Fig GPa and /…

A: Given data:

Q: 4. (a)Find the slope and deflection at A in the Figure. (b) Determine the location and the magnitude…

A: Given dataThe diagram of a double overhang beam is given find  use conjugate beam method1. Slope and…

Q: Determine the smallest cross-sectional area, (A) required for the members of the truss shown below,…

A: The solution is in step 2:

Q: USE VIRTUAL WORK METHOD TO DETERMINE THE DEFLECTION AT B. 30 KN/m 16KN А В D 2.4 3.2 1.8

A: To find out the deflection at B.

Q: Determine static indeterminacy

A: Introduction : In the given problem we know the number of joints , number of member and number of…

Beams and Frames

A beam is a horizontal structure or a member which is always subjected to transverse shear loads.