Perforating Gun creates holes in the casing string to connect the flow of formation fluid into the wellbore with cone-shaped explosive charges detonated inside.   Select one: True False

Q: Write the formula for the time required to fill the cavity by the bottom gating system.

A: Given: Bottom gating system

Q: A M12 x 1.25 hex-head bolt with a nut is used to clamp two 25-mm thick steel plates. The nut height…

A: Given:- Elastic modulus 207 GPa Bolt size= M12 x 1.25 Height of nut =10.8 To find:- d) Bolt…

Q: A force P passing through points A and B in the figure has a clockwise moment 300 ft-lb about O.…

A: The moment about O, M = 300 lb.ft

Q: Two forces P and Q pass through a point A w/c is 4 ft to the right of and 3 ft above a moment center…

A:

Q: Why is the remaining fluid at the delivery tip of a Mohr pipet is not blown out?

A: A Mohr pipette is a type of pipette that is used to measure the volume of any liquid solution…

Q: Convert to cis form

A: Conversion to cis form.

Q: The velocity field of an incompressible flow is given by V = (a,x + a,y + azZ)i + (b,x + b,y + b3z)j…

A: Answer: The value of b2 is 2.

Q: AV - belt (a = 36°) is used to transmit a couple from drum B to drum A. Knowing that the coefficient…

A: As the angle β is smaller for the pulley B, the belt will slip first at B β=180-215=150 In radian…

Q: How pilot tube works?

A: The pitot tube is a simple device that is used to measure the flow velocity with no moving parts.

Q: Determine the bar force of member AD (in kN) of the truss shown if P = 12 kN and Q = 60 kN. Use 3…

A:

Q: What is the maximum gas flow rate for a nozzle size?

A: GIVEN; What is the maximum gas flow rate for a nozzle size?

Q: What is the mass in grams and the weight in dynes ,gram force and in Newton of 12 oz salt? ma a. •…

A: Given that, Amount of salt, W=12 OZ salts Since, 1 OZ=28 gram=28 gHence,12 OZ=12×28 gram12 OZ=336…

Q: Imagine we are viewing the pipe from an Eulerian perspective. The pipe is heated with a Bunsen…

A:

Q: lockwise. F 15kN F -30° 2m 10kN 30° 10KN

A: Given,

Q: 25,000 cfm of outdoor air is brought into an HVAC system air handling unit (AHU). The air is at 100°…

A:

Q: A centrifugal pump is required to pump water to an open water tank situated 4 km away from the…

A:

Q: Que 5.15. Fig. 5.15.1 shows a steel rod of 12 mm diameter with one end fixed into a horizontal…

A: Here given data  D = 12 mm  = 12 x 10-3 Mass = m = 10 kg  Force = mg = 10*9.81 = 9.81 N Young's…

Q: The hand truck and its contents have a mass of 58 kg with center of gravity at G. (Eigure 1) Part A…

A:

Q: What is the minimum gas flow rate for a nozzle size?

A: Given: What is the minimum gas flow rate for a nozzle size?

Q: In the given figure, Find the y coordinate of point A so that the 361 lb force will have a clockwise…

A: Given :-  Force (F) = 361 lb Clockwise Moment about point O  = 400 ft lb To Find :- Y-coordinate of…

Q: How to find the diffliction of the string at any point

A:

Q: At the beginning of the compression process of an air standard Otto cycle, p1 = 1 bar, T1 = 300 K.…

A: given data; ⇒initial pressure (P1)=1bar=100KPa⇒initial…

Q: can you show a clear sloution

A:

Q: 1. A pole 30 m. high is shown supporting a wire in the xy plane. The wire exerts a force of 100 N on…

A: Given DataL=30m

Q: A vessel contains Nitrogen undergoes the following thermodynamics processes as stated below: Process…

A: Given data Gas contained : NitrogenProcess 1-2 : isothermal compression P1 = 800 kPa       V1 = 0.08…

Q: Determine the diameter of the piston rod of the hydraulic cylinder of 100 mm bore when the maximum…

A: Given data: D=100 mmP=11.6 N/m2L=1.2 mσy=300 MPaFOS=2.5 Need to determine the diameter of the piston…

Q: A fan with a flow rate of 0.34 m3/min will be used to cool a desktop computer.

A:

Q: Fihd stralh on strain gauge Given: sigma_x = 12.4 ksi sigma_y = 20.6 ksi E=10,000 ksi yield strength…

A: Given Data: • The length of the wire is 1= 1 m. The diameter of the wire is d= 0.1 mm. ΔΙ • The…

Q: Determine the following. a. Resultant moment at A b. Resultant moment at B c. Resultant moment at C

A: According to the details provided in the question, we need to calculate the moment at points A, B,…

Properties of Fluids

The term fluid represents a type of substance that can easily change its shape under any external pressure/force and can flow. Fluids can acquire any shape in which it is stored and can resist normal stresses but cannot resist shear stress in rest condition. Whenever external shear stress is applied to fluids, it starts to flow. The fluids may be liquid or gas. Example- water, air, etc.