A lawnmower stops running after a short period of time. The fuel tank filler cap is removed and an almost fuel tank of fuel is found, so the cap is reinstalled and the engine restarted. The engine runs again for a short time and then dies so the cap is removed again and the process repeats. Tech a says the problem may be due to a clogged vent in the fuel cap. The b says that the intake mainfold gasket may be defective. Who is correct?

Q: A simplified diagram of the propulsion for GOES-R, a weather satellite in GEO is shown. This is a…

A: Given:To find:This is a  ______ liquid propellant system that uses a  ______ system to maintain the…

Q: Explain the operation of TWO (2) way catalytic convertor which use in Sl engine. Explain how to test…

A:

Q: 14. A. limits the maximum output pressure of an electric gasoline fuel pump. 15. Which of the…

A: As per the guidelines we will answer the first three subparts for you, for the rest of the questions…

Q: How diesel fuel injector work?

A: A diesel fuel injector is a device that is used to introduce the fuel inside the combustion chamber.…

Q: Question 6 uontanes of the pressure carburetor system.

A: The main advantage of pressure carburettor system are - reducing icing tendency -better efficiency -…

Q: How does a piezoelectric injector work?

A: Solution:

Q: Explain the steps involved in disconnecting a fuel line on a vehicle with: Multiport fuel injection…

A: Question: The steps involved in disconnecting a fuel line on a vehicle with: Multiport fuel…

Q: Unburned HC and Carbon mono-oxide reduced in the exhaust gases if the A/F decreased True False

A: Unburned HC and Carbon mono-oxide reduced in the exhaust gases if the A/F decreased True False

Q: What happens when txv valves goes bad?

A: The symptoms of restricted TXV, A restricted metering device — thermostatic expansion valve or TXV —…

Q: A technician is inspecting a vehicle and finds the upper radiator hose is collapsed, and the cooling…

A: Given :-  A technician is inspecting a vehicle and finds the upper radiator hose is collapsed, and…

Q: What is the name of the component that opens the valves?

A: There is a special component on the valve which is used to open the value.

Q: Which of the following is similar to a PCV valve but is specific to diesel engines? PCM EGR AIR…

A: PVR (positive crankcase ventilation): The PVR valves are not required in diesel engines. The PCV…

Q: Explain and review the ff. 1.Fuel Tank 2. Fuel level indicator 3. Fuel lines 4. Pumps 5. Air…

A: According to the question we need to explain Following 1.Fuel Tank 2. Fuel level indicator 3. Fuel…

Q: What are the results and discussions in identifying the different components of the ICEs valve…

A: Engine valves are a primary component of the internal combustion engine and are used to allow the…

Q: An engine starts and runs briefly after a small quantity of fuel is put into the spark plug hole,…

A: An engine starts and runs briefly after a small quantity of fuel is put into the spark plug hole,…

Q: Coolant leaking into the combustion chamber produces what color smoke from the exhaust? Select one:…

A: We have to know

Q: 3) Outline the way the following system works:

A: Given data

Q: Technician A says it is important to note transmission fluid temperature when checking the fluid…

A: For level checking of transmission fluid its temperature is checked. Transaxle has fluid for…

Q: The dieseling is O a. the engine is still working without ignition. O b. Engine use diesel as fuel O…

A: To find: The dieseling is

Q: For Diesel engine, the turbocharger will increase the pressure of

A: In order to produce mechanical power, an IC engine needs fuel and air (oxygen). The amount of fuel…

Q: d. Check oil level & moisture content 19. If the main wire (coil) to the distributor and the coil to…

A: 19. if the main wire (coil) to the distributor and the coil to the switch are broken , replace them…

Q: the 2 separate

A:

Q: an engine is being discussed for lean running condition. technician A checks for air leak in the…

A: There are five factors that causes to run engine in lean condition. They are Fuel System Oxygen…

Q: When checking the exhaust system, the Certified Inspector must reject the vehicle if: It does not…

A: While checking the exhaust system the inspector must reject the vehicle if it has no muffler,…

Q: what is the component that is moving to allow fuel to be injected into the intake port

A: A carburetor allow fuel to be injected into the intake port.

Q: the oil pressure light stay on whatever the engine fis running, and the oil pressure has been…

A: Oil pressure light indicates that the pressure of the oil is within the specified limits. It will…

Q: What checks can be performed to know if the lubricating oil of an engine has been contaminated?

A: Techniques to check whether the lubricating oil is contaminated are as follows, Debris analysis Wear…

Q: what are the two tune up methods used for a variety of big bore cummins engines

A: There are two tune up methods used for a variety of big bore Cummins engines. OBC (Outer base…

Q: The injector pulse width is the __________   ___    ________ the injector opens and sprays fuel.

A: Given :-  The injector pulse width is the ........................... the injector opens and sprays…

Q: What are the major components of a Piston Engine fuel System What are their major functions or roles…

A: The function of engine fuel system is to store the fuel and  then supply it into the chamber of…

Q: Which type of oil filter uses an anti drain back valve to prevent it from emptying of oil when the…

A: Which type of oil filter uses an anti drain back valve to prevent if form emptying of oil when…

Q: Increasing engine speed will decrease the engine knocking tendency because: Select one: O a…

A: Given: To select the correct option.

Q: Explain the operation of TWO (2) way catalytic convertor which use in Sl engine. Explain how to test…

A:

Q: briefly 1. Valve lag 2. intake lag

A:

Q: Technician A says there is less heat energy in high octane gasoline and, therefore less power is…

A: Technician A says there is less heat energy in high octane gasoline and, therefore less power…

Q: Technician A says that excessive engine oil consumption can be caused by low oil levels. Technician…

A: Answer:- Technician B correct.

Q: What would happen if one of the Flow Controls were reversed in a cylinder?  What are the…

A: Consider the cylinder as an open system. To implement the flow controls, consider the control volume…

Q: The most popular combustion chamber.7 which is equipped with four valves per :cylinder is…

A: There are different types of combustion chambers 1. Hemispherical 2. Pentroof 3. Wedge 4. Bathtube…

Joining Processes

It is the process of permanent or temporary joining of two metal pieces with the help of heat or pressure. Two metal parts are assembled by applying an energy source for the formation of a single unit. The obtained joined metals cannot be fragmented easily with the application of any force.