%3!Q4: - For static system as shown in figure below, if k 50 N/mm, m =m2,u = 0.25 for the blocks m, and m2, tensions TI= 28.35N, spring elongation 5 mmand the force F1 m, cos 0 + m, sin 0. Find the inclination angle, Tension inother wire, and the mass of blocks. By using the Grammar method.T2m2T1mlF1

Answered: Image /qna-images/answer/a42ce63a-f3a5-4ce0-a640-5b34e55d21f9.jpg

%3D Q4: - For static system as shown in figure below, if k 50 N/mm, m, =m2, µ = 0.25 for the blocks m, and m2, tensions T1= 28.35N, spring elongation 5 mm other wire, and the mass of blocks. By using the Grammar method. T2 and the force F1 m, cos 0 + m, sin 0. Find the inclination angle, Tension in m2 ml F1

%3D Q4: - For static system as shown in figure below, if k 50 N/mm, m, =m2, µ = 0.25 for the blocks m, and m2, tensions T1= 28.35N, spring elongation 5 mm other wire, and the mass of blocks. By using the Grammar method. T2 and the force F1 m, cos 0 + m, sin 0. Find the inclination angle, Tension in m2 ml F1

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider the spring assemblage shown, using the direct stiffness method do the following: 1. Write the global stiffness matrix 2. Determine the nodal displacements 3. Determine the nodal forces 4. Determine the reaction of supports K1 = 15 kN/m f Node 1 F = 0.675 kN K2 = 45 kN/m No Node 2 X positive to the right vov Node 3 K3 = 15 N/m Node 4
5. A rod of length L, Young's modulus E, cross-sectional area A and mass density p is installed as shown. Suppose m = pAL and kL / EA =1. Find the equations of motion Open Question m www f(t) x=0 x = L/2 x= L
Q4 (a) Based on Figure Q4(a), the diaphragm in a differential pressure gauge deflects proportionally with the pressure difference across it. This deflection is used to measure the pressure difference, ôp. To operate well, the material must not fail under the loading, and it should have a large deflection in order to increase the sensitivity of the measurement. The equations below for maximum stress and of a circular diaphragm of fixed radius are important to answer this question. The diaphragm thickness is t, E is Young's Modulus, and v is Poisson's ratio. a² Omx = Ap 2t2 Здра" (1 — v?) 16E 3 Using the information above, explain how you would determine in different ways the M-value for this design. (Answer can be with or without doing the algebra)
7. A spring is attached to the floor. When a 125 g mass is placed on top of the spring it compresses by 0.26 m. What is the spring constant of this spring?
Plz solve using finite elemental method correctly
Write the global stiffness matrix of the spring assemblage shown. Assume that all springs remain horizontal, the vertical bars at nodes 2 and 3 are rigid and allowed to slide horizontally to the left or right. Node 1 K1 = 2000 lb/in K2 = 2000 lb/in Node 2 m K3 = 1500 lb/in K4 = 1500 lb/in Node 3 F = 250 lb ma K5 = 3000 lb/in Node 4
Parts A and B
Must solve all three questions. Dont solve it partially.
For the simple pendulum shown in the figure, write the governing equation in s-domain. Assume small angles and linearize your model. Initial conditions are zero. Explain each step clearly. - 0(1) L, length m, mass
Consider the following spring system. with spring constants c 1 Cy Assume down is the positive direction. Write the elongation matrix A Write the stiffness matrix K
2