%3D E. 6.42 6.40 57 R1.5 2.2 Ø82.6 (F) 17 -R2 R0.8 MAX 25.5 25.4 060 D. 035 28.6 28.4 MAX 051 45° MIN ø100 R3 Ø8.5 M10 X 1.5-6H- 45° -4X 010.5 |SF 019 V2 4X 90° NOTE: ALL DIMS IN mm UNSPECIFIED TOLERANCESI MATERIAL FIN. DIMS ±0.2 GRAY IRON THIRD ANGLE PROJECTION DVN BY R.C. SCOGGIN REDRAWN BY SCALE M. ŽOKVIĆ CHKD LS UNFIN, DIMS ±1 1:1 TITLE ANGLE 0° 30' DWG NO. FLANGED HUB 31A059

Q: 5. a) Define and illustrate with your own sketches 3 classes of fit that apply to a hole /shaft…

A: Fit is characterized as a degree of tightness or detachment between two mating parts to perform…

Q: What is the relationship between the degrees of freedom and the types of joints?

A: Given: Relationship between the degree of freedom and the types of joints

Q: What is the LMC of hole D?

A: LMC stands for Least Material Condition, which is the feature of the size of the object that…

Q: What happens when the boards are bonded together?

A: When the boards are bonded together with an adhesive material, the mechanical interlocking mechanism…

Q: How do you read the tolerance for the bolt?

A: Given :-  Bolt drawing   Find :-  How do u read the tolerance of the bolt = ?

Q: If the pitch of a thread is 1/18 inch, how many threads are needed for the threaded section of a…

A:

Q: I need the answers to this question.

A: The explanation of the above terms have been explained below.

Q: 1. Determine the tolerance allowed on the hole of the part.

A: Tolerance – the total allowable change in measurement; the contrast between the upper and lower…

Q: True or False? The largest diameter threaded rod is available only up-to 8-inches

A: The threaded rod has several different measurements associated with it. There is major diameter,…

Q: What is the direction of the threads?  RH??

A: Right-hand threads run in a clockwise course, while left-hand threads (as seen in our extend of…

Q: Provide any six types of flanges used in piping.

A: Here are six common types of flanges used in piping systems:Weld Neck Flange: Characterized by a…

Q: What size UNF bolt made from SAE grade 5 steel is needed to carry a static tensile load of 3000lb…

A:

Q: Technician A says a metric bolt with the marking of 8.9 has more yield strength than a 10.9 bolt.…

A: Technician A is not correct as the 10.9 grade bolt has more strength than 8.9 grade. Grade 10.9 is…

Q: In most cases, pre-loading a bolted tensile joint increases the fatigue factor of safety. has no…

A:

Q: 20 BUTT-2A .688 R. .626 DIA..003 5.50 13 812 6.000 -1.000 UNLESS OTHERWISE SPECIFIED: MATERIAL:…

A: 5. Pitch  6. BUTT is designation for  9. Standard or precision class of fit

Q: What is the flat to flat width of the bolt head

A: Let us discuss above engineering drawing in figure.

Q: If a spline is transmitting 2,000 lb-in torque, what would be the major spline diameter for a 4A…

A:

Q: M25x6-4h5h-23   describe each part

A:

Metrology of Screw Threads

Screw threads are a series of ridges having the profile of a helix. This helix profile runs continuously along the length of a uniform solid or a hollow bar of a circular cross-section at periodic intervals. These helix ridges are also formed over a conical bar. These continuous helical ridges are termed threads.