Answered: %, for No 200 -%finer 77. LL=63, PL=…

Engineering

Civil Engineering

%, for No 200 -%finer 77. LL=63, PL= 25. Classify the soil using USCS. Justify your answer. a. MH b. CL c. CH

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter3: Weight-volume Relationships And Plasticity

Section: Chapter Questions

Problem 3.1P

See similar textbooks

Related questions

Q: A sieve analysis test was performed on a sample of coarse aggregate and pro- duced the following…

Q: 1- The result of sieve analysis of three aggregate samples (A, B, and C) are given below. a) Design…

A: a} a1=Mix ratio of agg A=∑%P100=100+10.01+0.9+0.2×5100=1.1191a2=Mix ratio of agg…

Q: Q2. Using the sieve results of a batch of sand and gravel shown in the table below,calculate the…

Q: Q1. Fill the remaining columns for the sieve analysis data given in the table Weight of Empty…

A: Note: Since you have asked multiple questions, we will solve the first question for you. If you want…

Q: What is the cumulative percent retained on the sieve with the highest percent retained? (2 decimal…

A: We will take average of all three trials and find the cumulative percent retained.

Q: A sieve analysis test was performed on a sample of coarse aggregate and pro duced the following…

A: as per our guidelines we are suppose to solve only 3 sub part per post .kindly repost other sub part…

Q: Three samples of aggregates were taken weighed in moist and dry condition. Moist Dry Unit Absorption…

Q: For a soil specimen, the following are given: % passing Sieve No. 4 = 92% % passing Sieve No. 10 =…

A: Look at the % passing through No 200 sieve=65>35% silt and clay minerals

Q: C. Using the sieve results of a batch of sand and gravel shown in the table below,calculate the…

A: Finness modulus is the sum of cumulative percentage retained on each seive divided by 100.…

Q: if total sample mass of aggregate is 164.9 grams, then the percent passing from sieve size #50 only…

A: The given data is: Total sample mass of aggregates (WT) = 164.9 g

Q: What must be the minimum size (width) of chutes of the mechanical splitter if the dry fine aggregate…

A: For the dry fine aggregate in which the entire sample will pass the 9.5-mm (3⁄8-in.) sieve, a…

Question

For a given sieve analysis: No. 4 - % finer 100%, for No 200 -%finer 77. LL=63, PL= 25. Classify the soil using USCS. Justify your answer.

a. MH

b. CL

c. CH

d. CL-ML

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Material structure and physical properties

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

For a given sieve analyis: No. 4 - % finer 99%, for No. 200 -%finer 76. LL=60, PL= 32. Classify the soil using USCS. Justify your answer. a.CH b.MH c.CL d.OL
For a given sieve analyis: No. 4 - % finer 99%, for No. 200 -%finer 76. LL=60, PL= 32. Classify the soil using USCS. Justify your answer. provide fbd a.CL b.CH c.MH d.0OL
For a given sieve analyis: No. 4 - % finer 92%, for No. 200 -%finer 48. LL=30, PL= 8. Classify the soil using USCS. Justify your answer. CHOICES: a.SM b.SC c.MH d.GC
The specific gravity and absorption test (ASTM C128) were performed on fine aggregate. The following data were obtained.Given:Mass of SSD sand = 400.0 gMass of pycnometer with water = 520.0 gMass of pycnometer with water plus sand = 850.0 gMass of dry sand = 397.0 gRequired:a) absorption, in percentb) free moisture if the sand in the stockpile has a moisture content of 3% bbbbbbbbbbbbbb
all 5.21 A sieve analysis test was performed on a sample of aggregate and produced the results shown in Table P5.21. TABLE P5.21 Sieve Size, mm 25 19 12.5 9.5 4.75 2.36 Amount Retained, g 0 376.7 888.4 506.2 1038.4 900.1 live prised 1973 Sieve Size,TBA mm 1.18 0.60 0.30 0.15 0.075 Pan lusta) groads to storic Amount Retained, g 891.5 712.6 625.2 581.5 242.9 44.9 Calculate the percent passing through each sieve. Plot the percent passing versus sieve size on: a. a semilog gradation chart, and b. a 0.45 gradation chart (Figure A.25). What is the maximum size? What is the nominal maximum size?
Indian Standard (IS) Light Compaction test is usually conducted in 3 layers in a 1000 cc mould. How many blows per layer would be necessary if the above test is conducted in a 2250 cc mould? COMAN0aWaaww VWWOW¶D@W¶DWW¶DⱭvⱭ❤aww/D/¶DUDUDDWYD.
LL=24% and PL=21% Classity the soll using A. USCS (GROUP SYMBOL IS | GROUP NAME IS B. AASHTO (GROUP IS GI IS ) C. USDA (THE NAME OF THE SOIL IS
please answer in the nearest 3 decimal number. refer to MM = 07 and DD as 26
Q/ What the purpose from sand content measurement, what is the acceptable percentage and size partials
Please correct answer and detail solution
a. What is the cumulative percent retained on the sieve with the highest percent retained? b. What is the percent passing on pan?
The specific gravity and absorption test (ASTM C128) were performed on fine aggregate. The following data were obtained.Given:Mass of SSD sand = 400.0 gMass of pycnometer with water = 520.0 gMass of pycnometer with water plus sand = 850.0 gMass of dry sand = 397.0 gRequired:a) bulk dry specific gravityb) bulk SSD specific gravityc) apparent specific gravity aaaaaaaaaa