PBL 21.7 O NC crcuit has R=175 2, L=0.50 H,C= 22.5 µF,f = 60.0 Hz and AV_ =325 V a. Determine the impedance of the circuit. h Determine the maximum current in the circuit. c. Determine the phase angle and d. Determine the maximum voltage across each components. [188.72 N, 1.72 A, 21.98°, 301 V, 324.21 V,202.72 V] Show your work:

PBL 21.7 O NC crcuit has R=175 2, L=0.50 H,C= 22.5 µF,f = 60.0 Hz and AV_ =325 V a. Determine the impedance of the circuit. h Determine the maximum current in the circuit. c. Determine the phase angle and d. Determine the maximum voltage across each components. [188.72 N, 1.72 A, 21.98°, 301 V, 324.21 V,202.72 V] Show your work:

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

Help with part B pls
11. The rms current in an RLC circuit depends on the frequency of the power source as shown below. It reaches its maximum value at f= 80 Hz. Find the rms voltage applied to the circuit if R = 10 22, C = 198 µF, and L = 20 mH. A. 25 V B. 50 V C. 75 V D. 100 V E. 125 V Current (Amps) 25 6 2.0 15 1.0 0.5 50 100 Frequency (Hertz) 150 200 250
11. The rms current in an RLC circuit depends on the frequency of the power source as shown below. It reaches its maximum value at f = 80 Hz. Find the rms voltage applied to the circuit if R = 102, C = 198 µF, and L = 20 mH. A. 25 V B. 50 V C. 75 V D. 100 V E. 125 V Current (Amps) 2.5 2.0 1.5 1.0 0.5 50 100 Frequency (Hertz) 150 200 250
Determine the total impedance of the circuit shown below.
A series RLC circuit withR= 6Q; L = 0.1H and C = 0.2 F has no applied voltage. Find the 1 subsequent current if the initial charge on the capacitor is 10 C and the initial current is zero. А. i (t) (e-10t + e-50t) A 4 С. i (t) (e-10t e-50t) A = (e-10t 4 5 (e10t + e-50t) A 6 В. i (t) e50t) A D. i(t)
1. Find the steady-state current in the RLC-circuit given in the figure. Take R = 0.20, L = 0.1 H, C = 2 F and E = 220 sin 314t V. E(t) = E, sin ot
The mains ac supply in some countries is 110 V r.m.s at 50 Hz (sinusoidal). How much time will take one cycle of this ac supply? Select one: a. 0.02s b. 50s C. 314 s С. d. 0.00318
A. 500 ohm B. 1900 ohm C. 1700 ohm D. 300 ohm E. 1500 ohm
In a simple AC circuit shown on the right, C = 0.0045 F, L = 1.4 H, R = 45 Ω, and ΔV = ΔVmaxsin(ωt), where ΔVmax = 5.5 V and ω = 45 rad/s. a. Calculate the numerical value of Z in ohms. b. Calculate the numerical value of Imax in A. c. Calculate the numerical value of φ in radians.
9
In the circuit shown below, R= 200.0 2, C = 6.00 µE and the AC source is given by 8 = 170.0 sin (377t), where ɛ is in volts and t is in seconds. The magnitude of phase angle between the current and the source voltage is: H (AC R O a. 65.6 degrees O b. 35.0 degrees Oc. 45.0 degrees O d. 60.0 degrees O e. 72.4 degrees
A RLC series circuit has C = 5 x 10-³ [F], R = 100 [22], and L = 3 × 10-³ [H]. This circuit is connected to an AC supply that gives out 10 [V] at 600 [Hz]. Which of the following statements is true regarding the current and the voltage of the generator? A. The source voltage lags the current. B. The source voltage leads the current. C. The current leads the source voltage. D. The source voltage and current are in phase.