Part II. 1. Herschel-Buckley Equation An unknown non-newtonian fluid underwent theology analysis. Assuming the yield stress is 36.3 Pa. Determine the fluid behavior index, consistency coefficient and type of non-newtonian fluid. Shear Rate (1/s) Shear Stress (Pa) 1 159 10 260 20 312 30 350 40 380 50 407 60 430

Part II. 1. Herschel-Buckley Equation An unknown non-newtonian fluid underwent theology analysis. Assuming the yield stress is 36.3 Pa. Determine the fluid behavior index, consistency coefficient and type of non-newtonian fluid. Shear Rate (1/s) Shear Stress (Pa) 1 159 10 260 20 312 30 350 40 380 50 407 60 430

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An underwater device which is 2m long is to be moved at 4 m/sec. If a geometrically similar model 40 cm long is tested in a variable pressure wind tunnel at a speed of 60 m/sec with the following information, Poir at Standard atmospheric pressure = 1.18kg/m³ Pwater = 998kg/m3 Hair = 1.80 x 10-5 Pa-s at local atmospheric pressure and Hwater = 1 × 10-3 Pa-s then the pressure of the air in the model used times local atmospheric pressure is
Please solve this problem, Thank you very much! Figure is attached 1. liquids in rotating cylinders rotates as a rigid body and considered at rest. The elevation difference h between the center of the liquid surface and the rim of the liquid surface is a function of angular velocity ?, fluid density ?, gravitational acceleration ?, and radius ?. Use the method of repeating variables to find a dimensionless relationship between the parameters. Show all the steps.
The pressure drops 4P = P₁ P2 through a long section of round pipe can be written in terms of the shear stress Tw along the wall. Shown in Figure 3 is the shear stress acting by the wall on the fluid. The shaded region is a control volume composed of the fluid in the pipe between axial locations 1 and 2. Using the method of repeating variables, generate a relationship for pressure drop as a function of all other parameters Final ans AP = P μ (₁ AP= {(₂17₂) P₁ CV UPL м = (²1 ²² an! VPL O P.H. L V
Casson model often used to describe the shear stress vs. shear rate relationship in colloidal suspensions where particle aggregation might cause the measured viscosity to increase at low shear rates. shear stress τ and the appliedshear rate S were fitted to the Casson model as written as
The heat transfer coefficient is a nondimensional parameter which is a function of viscosity ? , specific heat cp (kJ/kg·K), and thermal conductivity k (W/m·K). This nondimensional parameter is expressed as (a) cp/? k (b) k/? cp (c) ? /cpk (d ) ? cp/k (e) cpk/?
I need the answer as soon as possible
Select the most suitable complement among listed options fe T) Real fluids (a) are viscous (b) possess surface tension (c) (d) possess all the above properties (e) 2) In a static fluid (b) fluid pressure is zero (c) linear deformation is small (a) resistance to shear stress is small (e) viscosity is nil. (d) only normal stresses can exist 3) When the flow parameters at any given instant remain same at every point, then flow is said to be (d) uniform (e) Static. (a) Turbulent (b) Steady state (c) laminar are compressible possess none of the above properties.
For a venturi meter given below, the volumetric flow rate is defined in terms of the geometrical parameters, the density of working fluid (p), and density of the manometer liquid (pm) as 4. Q = f(D, D2, A2, g, h, Pmv Pr) %3D Write down the balance equations and show your work to end up with an expression for the volumetric flow rate in terms of the variables defined above.
Torque T needed to rotate a disk in a liquid depends on the diameter D, the angular velocity w, the fluid density p and viscosity, and the distance from the wall x. Relate torque to the other variables using the MLT system. Justify reasons for the chosen repeating variables.
Speed is usually a function of density, gravitational acceleration, diameter, height difference, viscosity, and length. Using the repetitive variables method and taking density, gravitational acceleration, and diameter as repetitive variables, find the required dimensionless parameters. V = f(p, g, D, Az, u, L)
In the given image, both fluids are at 20°C. The specific weight of water is 9790 N/m³. If surface tension effects are negligible and a = 8.35 cm, what is the density of the oil, in kg/m³? Oil 6 cm Water Numeric Response CO 10 cm
There are many common dimensionless numbers used to describedifferent physical effects. Such dimensionless numbers are usually a ratioof specific properties, for example, the Reynolds number represents theratio of inertial to viscous forces.Choose three of the following dimensionless numbers and describe whatproperties the ratio represents and the context in which these numbers areimportant: Froude Number, Euler Number, Mach Number, Weber Number,Nusselt Number, Prandtl Number.