Part A The assembly consists of three titanium (Ti-6A1-4V) rods and a rigid bar AC. The cross- sectional area of each rod is shown. (Figure 1) If a force of P = 79 kip is applied to the ring F, determine the horizontal displacement of point F. Use Ęt = 17.4(103) ksi. xpress your answer in inches to three significant figures. Figure T AEF 2 in 1 ft E P F2 ft 2 ft C 6 ft B AAB = 1 in² ACD = 1.5 in² 6 ft D < 1 of 1 1 ΑΣΦ t vec SF = 0.169 Submit Previous Answers Request Answer × Incorrect; Try Again Provide Feedback ? in.

Part A The assembly consists of three titanium (Ti-6A1-4V) rods and a rigid bar AC. The cross- sectional area of each rod is shown. (Figure 1) If a force of P = 79 kip is applied to the ring F, determine the horizontal displacement of point F. Use Ęt = 17.4(103) ksi. xpress your answer in inches to three significant figures. Figure T AEF 2 in 1 ft E P F2 ft 2 ft C 6 ft B AAB = 1 in² ACD = 1.5 in² 6 ft D < 1 of 1 1 ΑΣΦ t vec SF = 0.169 Submit Previous Answers Request Answer × Incorrect; Try Again Provide Feedback ? in.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter9: Moments And Products Of Inertia Of Areas

Section: Chapter Questions

Problem 9.13P: Figure (a) shows the cross section of a column that uses a structural shape known as W867...

See similar textbooks

Similar questions

correct ans
An engineer determines that a 60 cm long rod of 1045 HR grade of steel will be subjected to a tension of 20kN. The following two designs requirements must be met: must remain below 145MPa and the rod must stretch less than 0.125mm. Determine an appropriate value for the rod's diameter to meet these two requirements. Round to the nearest milimeter
answer 24mm
One shaft is in torsion as shown below. If the magnitude of shear stress at point A is 345.6 MPa, calculate the magnitude of the shear stress at point B on the same cross-section as point A: MPa. Calculate your answer to 1 decimal place. 40 mm 30 mm T
Find Ixx of the plate shown below. where AB = 2 m, AC=12.5m, EF = 10m, FG = 2.5m, HD=3m. A B (1) E F (Enter only the values in the boxes by referring the unit given in bracket.) C The value of X (in m) = The value of Y (in m) = The value of lw1 (in m) = The value of lw2 (in m4) The value of Ix of the given plate (in m4) =
The square deforms into the position shown by the dashed lines. (Figure 1) The dimensions are S = 55 mm, S' = 60 mm, Az1 = 5 mm, and A₂ = 8 mm. Side D'B' remains horizontal. Figure 91.5 ATL Ax₂ 1 of 1
The axial load 229kN applied to the lap joint is distributed equally among the three 17.1-mm-diameter rivets. What is the maximum tensile stress (in Mpa) in the plate if w=139.6mm and t=29mm? Round off the final answer to three decimal places.
Show the correct FBD please. The answer must be TA=TB=20.4 lb, TC=27.2 lb
Please don't provide handwritten solution ....
3
W2 h2 h1 E W1> Calculate y, the distance from the base to the position of the Neutral Axis of the T-section shown above (not drawn to scale). The bottom section has width wi = 5mm and height hị = 90mm. The top section has width w2 = 120mm and height h2 = 14mm. Enter your answer in millimetres correct to two decimal places. mm
1 0 Calculate the total volume of the cylindrical component below (not to scale): L1 D1- D1 = 1.12 cm D2 = 0.71 cm D3 = 1.58 cm L1 = 18.68 cm L2 = 15.36 cm L3=13.77 cm L4 = 9.77 cm Answer: Check L2 L3 L4 D2- What is the volume of the cylindrical component? (State your answer in S.I. units (m³), accurate to 3 significant figures) D3