P1 = 50 KPa P2 = 10 KPa 4m OIL 1.6m OIL In the figure, an orifice is locates in the partition wall so that it discharges oil (SG = 0.8) from left to right side of the room. The orifice has a diameter of 100mm and is under the surface of oil, 4m from the surface the left and 1.6m from the surface on the right. The surface at the left is under 5OKPA of pressure and the surface at the right side is under 10KPA of pressure. Determine the actual discharge in the orifice if C = 0.92 A) 87.63 L/s B) No Answer among the choices c) 95.25 L/s 103.07 L/s E) 112.03 L/s

P1 = 50 KPa P2 = 10 KPa 4m OIL 1.6m OIL In the figure, an orifice is locates in the partition wall so that it discharges oil (SG = 0.8) from left to right side of the room. The orifice has a diameter of 100mm and is under the surface of oil, 4m from the surface the left and 1.6m from the surface on the right. The surface at the left is under 5OKPA of pressure and the surface at the right side is under 10KPA of pressure. Determine the actual discharge in the orifice if C = 0.92 A) 87.63 L/s B) No Answer among the choices c) 95.25 L/s 103.07 L/s E) 112.03 L/s

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A vertical rectangular gate 2.2 m wide and 4.0 m high is submerged in oil (SG-0.87) with its bottom edge is 13.6 m below the water surface. Find the location of the center of pressure, measured from the liquid surface (in meters). Answer in two decimal places. Numerical values only. Don't indicate units here, just on the submitted solution. DOD F5 F6 F7 F8 F9 F10 F11 F12 5 6 7 8 P H
Example 7: The figure below shows a complex manometer. Calculate: 1. The gauge pressure of the air in the tube (2943 N/m²). 2. The gauge pressure at A (20718.72 N/m²). 3. The absolute pressure at A if the atmospheric pressure is 105Nm2 (120718.72 N/m²). s.g.= 0.90 S.g.= 2.94 B Air 0.6m 0.3m D FU 0.8m Water Density of water = 1000 kg/m³.
NEED HELP. PLEASE ANSWER ASAP. WILL UPVOTE
15. The inverted U-tube manometer is used to measure the difference in pressure between water flowing in the pipes at A and B. If the top segment is filled with air, and the water levels in each segment are as indicated, determine the pressure difference between A and B. pw = 1000 kg/m³. 75 mm 225 mm 150 mm C D B 300 mm
Note:hand written solution should be avoided.
Determine the minimum size of glass tubing (mm) that can be used to measure water level, if the capillary rise in the tube is not to exceed 0.1496 mm. Take surface tension of water in contact with air as 0.0735 N/m.
Given: 4 tank full of water and oil (Set 0.80), as shown. Find: The pressure at the oil water interface and the bottom of the tank. %3D 0.9 m Oil (S = 0.8) 0.9%o Water, T 10° C 2.1 m 2.14 0.9 2.
Fluid 5
P10.) Determine the flow in each pipe shown in the figure. Assume f = 0.02 for all pipes. Subject: fluid mechanic Lesson: *Conservation of Energy *Fluid Flow in Pipes