| My courses / ENCN231-22S1 / Sections / Quizzes / Quiz 4Draw and label the shear and moment diagrams for the beam and loading shown below. For thisQuiz navigationcase: w =2 kN/m, a = 2.2 m, and c =1.4 m. The cross-section of this beam has a height h = 155mm and a width b = 44 mm.WFinish attempt...AhCX) B|CaFor full marks, your submitted working must include fully labeled shear and moment diagrams.Determine the magnitude of the maximum bending moment in the beam in terms of absolutevalue. Express your result in units of kNm with 2 decimal places of accuracy.Mmax = |kNmтах

Answered: Image /qna-images/answer/ad0a1c78-ed1b-4df0-9066-725a7f02e27c.jpg

| My courses / ENCN231-22S1 / Sections / Quizzes / Quiz 4 Draw and label the shear and moment diagrams for the beam and loading shown below. For this Quiz navigation case: w = 2 kN/m, a = 2.2 m, and c = 1.4 m. The cross-section of this beam has a height h = 155 mm and a width b = 44 mm. W Finish attempt ... A В C a For full marks, your submitted working must include fully labeled shear and moment diagrams. Determine the magnitude of the maximum bending moment in the beam in terms of absolute value. Express your result in units of kNm with 2 decimal places of accuracy. Mmax = | kNm

| My courses / ENCN231-22S1 / Sections / Quizzes / Quiz 4 Draw and label the shear and moment diagrams for the beam and loading shown below. For this Quiz navigation case: w = 2 kN/m, a = 2.2 m, and c = 1.4 m. The cross-section of this beam has a height h = 155 mm and a width b = 44 mm. W Finish attempt ... A В C a For full marks, your submitted working must include fully labeled shear and moment diagrams. Determine the magnitude of the maximum bending moment in the beam in terms of absolute value. Express your result in units of kNm with 2 decimal places of accuracy. Mmax = | kNm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

PROBLEM 1 Using the loading diagram for the frame shown below, complete the following: Draw the free body diagrams for AB and BDE. 。 NOTE: the beam is continuous at point 'D' • Determine the reactions at 'A' and 'C' • Determine the shear, moment, and axial load at point 'X' noted on the sketch below. Point 'X' is located four feet (4'-0") above point 'A' METAL DECK OVER STEEL FRAMING EL: +16'-0" EL: +12'-0" CONCRETE RETAINING WALL- B 24'-0" 14'-0" 6'-0" 3'-0 D E EL: +0'-0" A FU C Page 2 of 4 CRANE + PULLEY SYSTEM MATERIALS "RAIL" SYSTEM EL:-4'-0"
For the same beam and loading shown, what is the slope at Point A? C B. -L- -L/2- O-(WL)/8EI O (WL^3)/6EI O (wL^2)/8EI
B2
Simply Supported Beam ABCDE below carries multiple loads as shown. A built-upsection made from a T-Section and a Channel (C-Section) fastened together by 16mm∅ bolts,equally spaced from the center of the section, with shearing capacity τ=100 MPa, for bearing σb= 220 MPa for rivets in single shear and σb = 280 MPa for rivets in double shear. E=200GPa forall materials. Determine the moment capacity of the section, kN-m, if fbcap≤300 MPa.
I. Solve the given problem below. 1. Atension member has a span of 7.6 m and carries a tensile load of 512 kN. The member is to have two lines of rivets in each flange for the 20 mm rivets with standard diameter of 22 mm for hole dimension with at least 3 rivets in a line. Using an A 36 W section and neglecting the weight of member, design a W section. Fy 248 MPa and Fu = 400 MPa. Possible Sections: W 8 x 17 A = 3232 mm2 d = 200 mm r=85.34 mm ry 30.99 mm t = 7.82 mm b 133.4 mm W 5 x 18.5 A = 3503 mm2 d = 130 r= 54.86 mm ry = 32.51 mm tr 10.67 mm b = 127.6 mm W 250 x 67 A = 3794 mm2 d = 157 r= 67.56 mm ry 38.35 mm tr = 9.32 mm br = 152.9 mm %3D %3D %3D %3D %3D
Q3: A cast-iron bracket has a cross section and subjected to loading shown; A) If the compressive stress in top flange is not to exceed (17.5 MPa), what is the moment, the section can take? B) If the section is subjected to a shear force of (100 kN), draw the shear stress distribution over the depth of the section. 50 T 250 50 T 250- 150- 50
Simply Supported Beam ABCDE below carries multiple loads as shown. A built-upsection made from a T-Section and a Channel (C-Section) fastened together by 16mm∅ bolts,equally spaced from the center of the section, with shearing capacity τ=100 MPa, for bearing σb= 220 MPa for rivets in single shear and σb = 280 MPa for rivets in double shear. E=200GPa forall materials. Determine the moment of inertia of the section in x10^6 mm^4
Questions 3 and 4 only
Hw Draw S.f,B.M and elasticdiagvams for the beam shown beloi by using method of equations? 4 KN Im Im 4m 2m
ㅏ 2m 2P 2m B Im 4cm 8cm 4cm 4cm 12cm 4cm An overhanging beam is constructed by four wood plates with rectangular cross-section by nails as shown in the figure. If the allowable stresses are oo-10 MPa and t-1 MPa: a) Determine the load P that the beam can carry safely. b) If each nail can support a shear force of Q=2 kN, determine the required nail spacing e using the load P calculated in question (a).