One plate (with k=15W/m-K, p=6500kg/m3, cp=450J/kg-K, thickness of 0.2m, and initial temp of 465K) is pushed against another plate (with k=10W/m-K, p=4000kg/m3, cp=525J/kg-K, thickness of 0.2m, and initial temp of 375K) both having their opposite sides insulated. After a total of 115 seconds passes (since the plates touch), what is the temperature of the hotter plate's exposed surface?

One plate (with k=15W/m-K, p=6500kg/m3, cp=450J/kg-K, thickness of 0.2m, and initial temp of 465K) is pushed against another plate (with k=10W/m-K, p=4000kg/m3, cp=525J/kg-K, thickness of 0.2m, and initial temp of 375K) both having their opposite sides insulated. After a total of 115 seconds passes (since the plates touch), what is the temperature of the hotter plate's exposed surface?

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.8.9P: Two sections of steel drill pipe, joined by bolted flange plates at B, arc subjected to a...

See similar textbooks

Similar questions

3. The hydraulic cylinder shown in the figure has a D = 6.7-cm bore and is to operateat a pressure of 11 MPa. With the clevis mount shown in figure for Q. No. 3, thepiston rod should be sized as a column with both ends rounded for any plane ofbuckling. The rod is to be made of forged AISI 1030 steel without further heattreatment.(a) Use a design factor nd = 2.5 and select a preferred size for the rod diameterif the column length is 2 m.(b) Repeat part (a) but for a column length of 51cm.(c) What factor of safety actually results for each of the cases above?
3) The deflecting torque in a spring-controlled instruments is 1.2 × 10–4 kgm for a deflection of 90°. The control torque is exerted through a phosphor-bronze spring whose Young's modulus is 1.15×1010 kg/m2 of the allowable maximum stress is 5.5 × 106 kg/m2 and width of spring strip is 0.75 mm, And the thickness and length of suitable dimensions for the spring-strip. [Ans. 0.685 m, 0.4175 mm]
MN = 46
Q8
Can you please simplify the solution for this problem. Kindly clarify also if I am wrong I think our prof forgot to put the cos(10) for the distance of the restultant. (For the solution below)
Consider the steel pressure vessel shown in Figure 1, intended to withstand an internalpressure of 40 MPa. The vessel has an outer diameter of 300 mm, an overall length of 500mm and a wall thickness of 30 mm. There is a 30 mm fillet radius where the interior wallsurface joins the end caps, as shown in the section view in Figure 1. The vessel is made ofASTM A27 steel. Use ANSYS Workbench to simulate this component and comment on itssuitability for production given the loading conditions detailed above.
1. A rotating l-in diameter solid round bar has a groove 0.1-in deep with a 0.1-radius machined into it. The bar is made of AISI 1020 CD steel and is subjected to a purely reversing torque of 1800 lbf-in. For the S-N curve of the material, let f= 0.9. 1) Estimate the number of cycles to failure. 2) If the bar is also placed in an environment with a temperature of 750 °F, estimate the number of cycles to failure. Note: for pure shear stress state, find ta and Tm to replace oa and om. Apply the load factor k. = 0.59. To get safety factor against first-cycle yielding, use Sgy=0.577 Sy (based on DE theory). For fatigue life or fatigue failure criteria, Replace Sut with Sgu. Ssu = 0.67Sµt
3. The safe working stress of a belt is equal to the tight side tension over the product of the belt's width and thickness. Find the width of the belt if a 610mm diameter pulley transmits 40 kW at 500 rpm, the arc of contact is 144°, coefficient of friction is 0.35, safe working stress of the belt is 2.1 MPa and thickness is 6mm.
Repeat the previous problem using sx= 12 MPa.
A countershaft carrying two V-belt pulleys is shown in the figure. Pulley A receives power from a motor through a belt with the belt tensions shown. The power is transmitted through the shaft and delivered to the belt on pulley B. Assume the belt tension on the loose side at Bis 15 percent of the tension on the tight side. Given: TA1= 550 lbf, TA2=82.5 lbf, dA=6 in, dg 7.5 in, and dshaft=1.292 in. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. TAI TA A(DA) dehaft B(da) At the point of maximum bending moment, determine the bending stress and the torsional shear stress. The bending stress at the point of maximum bending moment is kpsi. The torsional shear stress at the point of maximum bending moment is kpsi.
A thin gas cylinder with internal radius of 100 mm is subjected to internal pressure of 10 MPa, per = 100 MPa. Efficiency of longitudinal and circumferential joints are 90% and 85%. Minimum cylinder wall thickness for safe design is mm
given: - initial length of steel tube= 200mm - aluminum rod is 0.175 mm shorter than steel tube. - l=0.175 mm properties of materials - ALUMINUM: coefficient of linear expansion: 23x10-6 /C modulus of elasticitty= 70 GPa - STEEL Coeficient of linear expansion: 11x10-6 /C Modulus of elasticity: 200 GPa *NEGLECT SHEAR AND LATERAL DEFORMATIONS. REQUIRED: - which of the two members will have contact on the rigid switch first and at what temperature - axial stress that would develop on 1st member after the 2nd material fills in the gap safely. PLS. SHOW FULL SOLUTIONS WITH BRIEF EXPLANATIONS AND NECESSARY DIAGRAMS...