A rod with a cross-sectional area of A and loaded in tension with an axial force of P = 2000 lbf undergoes a stress ?. Using a material strength of 24 kpsi and a design factor of 3.0, determine the minimum diameter of a solid circular rod

Q: The rigid bar AB shown below is supported by a steel rod AC having a diameter of 20 mm, and a block.…

A: Given data  Diameter of rod AC = 20 mm Distributed load on AB = 4 kN/m Find the axial normal stress…

Q: Axial loads are Bronze Aluminum Steel applied to the compound rod that is composed of an aluminum…

A:

Q: A solid round bar of diameter 250mm has a tensile force of 0.2kN acting on it. What is the stress…

A:

Q: What will be the cross-sectional area in mm² of the prismatical bar of length 5 mm and weight per…

A:

Q: PROBLEM 1 A rigid bar is attached to two vertical rods before a load is applied. Compute the…

A: As per given  P=50Kn Aluminum  A=500m2 L=4m E=70gpa Steel A=300mm2 L=3m E=200gpa We have to…

Q: What is the stress in a rectangular rod that is 20 mm by 30 mm in cross-section if is supporting a…

A: Given data:- load =1000 Ncross-section area =20 mm 30 mmTo find:-the stress in a rectangular rod (…

Q: 1. Steel rod 2.5m long is secured between tow walls. If the load on the rod is zero at 20°C, compute…

A: Solution 1: (a). Assume the rod to be disconnected from the rigid wall. The the temperature…

Q: Calculate the largest load p on AB in order to keep AC safe:

A: Uniformly distributed load:- Force is evenly distributed over the span of beam It is given that,…

Q: A rod with a cross-sectional area of A and loaded in tension with an axial force of P = 2000 lbf…

A:

Q: A copper rod of diameter 10 mm and length 4 m has a tensile force of 5 kN applied on it . Modulus of…

A:

Q: Steel Bronze Area (mm) 600 300 3. Figure (a) shows a rigid bar that is supported by a pin at A and…

A:

Q: The part shown is made from AISI 1040 CD steel and is loaded at point C with 300 N in the positive y…

A: Given : material - AISI 1040 CD diameter of bar d = 12 mmYield strength for AISI 1040 CD is 415 MPa

Q: Q31 A 75 mm diameter compound bar is constructed by shrinking a circular brass bush onto the outside…

A:

Q: The bell-crank mechanism is in equilibrium for an applied load of P = 22,kN. Assume that a = 260 mm,…

A: To calculate the average shear stress in the pin at B

Q: What will be the cross-sectional area in mm² of the prismatical bar of length 5 mm and weight per…

A:

Q: Please solve with step by step solution. A belt pulley is fastened to a 70 mm diameter shaft…

A: To find: The thickness of the key. Given: The speed of shaft is N1=200 rpm and N2=240 rpm. The…

Q: A machine component is subjected to flexural stress which fluctuates between + 280 MPa and – 137…

A:

Q: Design a knuckle joint subjected to axial tensile force of 50 kN. Determine the dimensions and the…

A: Given: Syt=500 MPaFOS = 3P=50 kN

Q: A long, flat steel bar 260mm wide and 35mm thick has a circular hole 50mm in diameter, centrally…

A:

Q: The average circumferential stress

A: Given data;   Thin cylinder of ,Inner radius , =500 mmThickness= 10 mmInternal pressure=5 MPa We…

Q: s shown in Figure Q1. Dimensions th of 90 MPa. The diameter of the etion at A:

A:

Q: A stainless steel tube with an outside diameter of 52 mm and a wall thickness of 5 mm is used as a…

A:

Q: A rod is subjed by a compressive load of 60,000 lb with shock. It is made of AISI 3140 OQT 800°F.…

A: Given the load = 60000 lb, and nature is shock  So the ultimate strength of AISI 3140 OQT 800°F…

Q: TEST I: 1 Find Mhe allowable safe load P if the stresses in the bar are the folbuwing. AB= 56 cgi…

A: Given data:-Stress in bar AB, σAB=50ksi=344.738N/mm2Stress in bar BC, σBC=60ksi=413.685N/mm2Stress…

Q: A steel disk with a 150 mm outer diameter is to be press fit to a hollow steel tube whose outer…

A:

Q: When a hydraulic cylinder is firmly anchored and pushing on a guided load, the effective length of…

A: Effective length of rod (le)= 2 m =2000 mm Diameter of rod (d)= 3.8 cm= 38 mm yield stress for 304…

Q: compression force of 50 N applied on the round bar of 500 mm diameter,  Calculate the stress…

A: Given:compressive force, F=50 Ndiameter of the round bar, d=500 mm or 0.5 m

Q: Rod of diameter 20 mm is loaded with 5kN tension force. What is the magnitude of stress in the rod?

A: Given, Diameter of rod = d = 20 mm Force applied to rod = F = 5 kN = 5000 N   Cross-sectional area…

Q: Problem # 5 When the temperature is vaised from 293.15 k to 333.15 k steel rod long and 50 mm?)…

A: Given data: The young's modulus of steel is 210 GPa.

Q: 2 A hollow steel tube with an inside diameter of 110 mm must carry a tensile load of 480 kN.…

A:

Q: ased on the yield stress rk out the allowable lo

A: A= 20x20= 400 mm2 Yield strength = 250 MPa F(s) = 4 Allowable stress = ? Working load =?

Q: O Torsion Аxial O Bending Transverse Shea O O

A: At point B the most impact on design will be of torsional shear stress, caused by the torsion.

Q: Calculate the normal stress in each segment if P=375KN. The cross-sectional area for each layer is…

A:

Q: A diagonal aluminum alloy tension rod of diameter d and initial length / is used in a rectangular…

A: The given data  d=0.55in l=7.4ft Allowable stress = 21 kpsi  Find the stretch in rod

Q: WERS. I WILL REPORT

A:

Q: A link in an automated packaging machine is a hollow tube made from 6061-T6 aluminum. Its dimensions…

A:

Q: with a stress of 52.89  and diameter of 4cm and thickness of 2mm  (P) load of 2MPa how was the…

A: