Oil discharges from a pipe through a sharp-crested round orifice as shown. The coefficients of contraction and velocity are 0.62 and 0.98, respectively. Calculate the actual discharge through the orifice, the actual diameter and actual velocity in the jet. 300 mm 75 mm Oil, s= 0.85 750 mm 180 mm Mercury

Oil discharges from a pipe through a sharp-crested round orifice as shown. The coefficients of contraction and velocity are 0.62 and 0.98, respectively. Calculate the actual discharge through the orifice, the actual diameter and actual velocity in the jet. 300 mm 75 mm Oil, s= 0.85 750 mm 180 mm Mercury

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The total head of fan is 200m and has a static pressure of 201mm of water gage. What is the velocity of air flowing if density is 1.16kg/m3. ANSWER: 22.9
Water is pumped through 750 ft of 6-inch nominal diameter Schedule number 40 pipe. The difference in height between the exit and inlet planes is given as 50 ft. Pump Efficiency 80% Pump Motor Power is 20 Horsepower. Friction losses are shown as 50 ft-lbf / lbm. Calculate the flow in the pipeline
What are the flow Q and the velocity V when total head loss is H = 25 m?
On the head side of a hydraulic cylinder, the rod is 1/2 inch in diameter and the piston is 2 inches in diameter. Calculate the force applied while retracting the rod and the speed at which it moves if the operating pressure is 150 psi and the flow rate is 6.5 gpm. Answer is incomplete without units.
The diameter of a pipe changes gradually from 75 mm at a point A, 6 m above datum, to 150 mm at B, 3 m above datum. The pressure at A is 103 kPa and the velocity of flow is 3.6 m/s. Neglecting losses, with the aid of a neat sketch, determine the pressure at B
The diagram shown illustrates the flow in a circular metal duct 20 feet long. The duct has a sudden contraction at the inlet and sudden expansion at the outlet. The diameter of the duct is 10 inches and the flow rate is 600 cfm. The duct is such that both ends have area ratio of 0.6. Thus A2/A1 = A3/A4 = 0.6. Calculate:(a) Pressure loss in the duct due to sudden contraction (in. wg.).
Water flows at a rate of 500 gal/min through a 400-ft-long line. The first and last 100 ft of the line are 6-in-diameter cast iron pipes, while the middle 200 ft consists of two 4.24-in-diameter cast iron pipes. Find: a. Provide a diagram b. the average velocity in each section of pipe, c. the pressure drop in each length of pipe, and d. the total pressure drop.
The discharge velocity is 49 m/sec and 227 mm water gage. The suction pressure is 48 mm water vacuum and velocity of 3 m/s. Calculate the fan total head in terms of water. Answer in cm.
Answer is 17.4N horizontally and 17.8N vertically.Please show steps in detail.
B1. A crude oil of specific gravity 0.75 is flowing through a pipe of diameter 275 mm and the frictional head loss of 5 m of crude oil between the two ends of a pipe which are 525 m apart. Calculate the Reynold's Number, discharge of crude oil in the pipe. Take co - efficient of friction as 0.007 and kinematic viscosity as 10 stokes. (Enter only the values by referring the unit given. Also upload the hand written answers in the link provided) The velocity of flow of oil in the pipe is (m/s) The Reynold's Number for the flow is Discharge of crude oil through pipe (in m3/s) is
Ethyl alcohol flows in the pipe as shown in Figure below of specific weight 19 lb/ft^ 3 . What is the mass flow rate? If viscous effects are neglectedTake the specific weight for mercury equal to 846 and for water equal to 62.4 at 68 F