O c. 7.5 x 10-70.mO d. 3.0 x 10-70.mOf the following, the copper conductor that has the least resistance is:Select one:O a. Thin, long, and hotO b. Thick, short, and coolO C. Thick, long, and hotO d. Thin, short, and coolA particle with a charge q located inside cubical gaussian surface. If the particle is at the cenflux through each face of the cube?Select one:REDMI NOTE 9AI QUAD CAMERA. depends on the size of the cube

Answered: Image /qna-images/answer/893fd0fb-51f4-4a46-8c64-e0375bc30d1f.jpg

Answered: Of the following, the copper conductor…

Of the following, the copper conductor that has the least resistance is: Select one: O a. Thin, long, and hot O b. Thick, short, and cool O C. Thick, long, and hot O d. Thin, short, and cool

Physics for Scientists and Engineers: Foundations and Connections

1st Edition

ISBN:9781133939146

Author:Katz, Debora M.

Publisher:Katz, Debora M.

Chapter24: Electric Fields

Section: Chapter Questions

Problem 40PQ

See similar textbooks

Related questions

Q: Question 1 ♥ Part (a) I measure the resistance of this wire and find it to be R = 156 Q2. What is…

Q: If your wet skin has a resistance of 1kΩ, and a lethal current is 100 mA, what minimum voltage is…

Q: Use the circuit given to the right to do the following: a. Determine the voltage across each…

A: According to Ohm's law , the voltage across the circuit is calculated by using the formula V=IR ,…

Q: find the electric field at r =3 meters.

A: Given data: The potential difference is: ∆V=30 V The electric field is: E The charge on a long wire…

Q: ong would it take to energy in one gallom

A: Given data: Power provided by electric system of home is 100 A with 220 V.

Q: An electric flat iron draws a current of 15 A when connected to a 110 V line. a. What is the…

A: Given data: Current (I) = 15 A Voltage (V) = 110 V Length (L) = 2.5 cm = 0.025 m Cross sectional…

Q: If the current in conductor is halved, what happens to?: electron drift velocity? current density…

A: Given: The current in the conductor is halved. (1) Write the expression for the electron drift…

Q: How many electrons pass through a 20-W resistor in 10 min if there is a potential drop of 30 volts…

A: Given: The power is 20 W. The time interval is 10 min. The potential drop is 30 V.

Q: A 10 volt ideal battery is in a circuit with three light bulbs, each with 29 of resistance, and a…

Q: Q18. A light bulb is rated 60 W, 120 V. If the bulb is connected to a 60 V battery, what is the…

Q: An electric device delivers a current of 0.5 A for 10 seconds. How many electrons (1.6x10-19C) flow…

A: Given: Current, I = 0.5 A. Time duration, t = 10 s. To Find: The number of electrons flow through…

Q: The resistivity of an ohmic material depends on ______. 1 p A. Resistance B. Length of the conductor…

Q: 2os2 3052 352 652 552 (2A

Q: R₂ = R₁ = R₁ = Rg = 100 3. A circuit containing five resistors connected to a battery with a 12 V…

Q: A current of 5.0 A flows through an electrical device for 10 seconds. How many electrons flow…

A: Answer : Option A , Option B and Option E

Q: 8] A length of copper wire has resistance of 0.172 S and a cross sectional area of 7.85 × 10–5 m²…

A: Length will be given as L = RA/rho =0.172 x 7.85 x 10-5 /1.72x 10-8 = 785 m

Question

O c. 7.5 x 10-70.m
O d. 3.0 x 10-70.m
Of the following, the copper conductor that has the least resistance is:
Select one:
O a. Thin, long, and hot
O b. Thick, short, and cool
O C. Thick, long, and hot
O d. Thin, short, and cool
A particle with a charge q located inside cubical gaussian surface. If the particle is at the cen
flux through each face of the cube?
Select one:
REDMI NOTE 9
AI QUAD CAMERA
. depends on the size of the cube

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.

Similar questions

(a) Will the electric field strength between two parallel conducting plates exceed the breakdown strength of dry air, which is 3.00106 V/m, if the plates are separated by 2.00 mm and a potential difference of 5.010V is applied? (b) How close together can the plates be with this applied voltage?
(a) What is the final speed of an electron accelerated from rest through a voltage of 25.0 MV by a negatively charged Van de Graff terminal? (b) What is unreasonable about this result? (c) Which assumptions are responsible?
(a) Find the voltage near a 10.0 cm diameter metal sphere that has 8.00 C of excess positive charge on it. (b) What is unreasonable about this result? (c) Which assumptions are responsible?
(a) Will the electric field strength between two parallel conducting plates exceed the breakdown strength for air ( 3.0 106 V/m) if the plates are separated by 2.00 mm and a potential difference of 5.0 103 V is applied? (b) How close together can the plates be with this applied voltage?
The practical limit to all electric field in air is about 3.00106 N/C. Above this strength, sparking rakes place because air begins to ionize, (a) At this electric field strength, how far would a proton travel before hitting the speed of light (ignore relativistic effects)? (b) Is it practical to leave air in particle accelerators?
An electron has an initial velocity of 5.00106m/s in a uniform 2.0010m/s electric field. The field accelerates the election in the direction opposite to its initial velocity, (a) What is the direction of the electric field? (b) How far does the electron travel before coming to rest? (c) How long does it take the electron to come to rest? (d) What is the electron's velocity when it returns to its starting point?
Suppose Earth and the Moon each carried a net negative charge Q . Approximate both bodies as point masses and point charges. (a) What value of Q is required to balance the gravitational attraction between Earth and the Moon? (b) Does the distance between Earth and the Moon affect your answer? Explain. (c) How many electrons would be needed to produce this charge?
A clock battery wears out after moving 10,000 C of charge through the clock at a rate of 0.500 mA. (a) How long did the clock run? (b) How many electrons per second flowed?
A 12.0-V battery-operated bottle warmer heats 50.0 g of glass, 2.50102 g of baby formula, and 2.00102 g of aluminum from 20.0C to 90.0C . (a) How much charge is moved by the battery? (b) How many electrons per second flow if it takes 5.00 min to warm the formula? (Hint: Assume that the specific heat of baby formula is about the same as the specific heat of water.)
A large parallel-plate capacitor is attached to a battery that has terminal potential (Fig. 27.15A). After a period of time, the capacitor stores charge Q so that its top plate is positive and its bottom plate is negative, and the potential difference between the plates is VC = . An I-shaped neutral conductor consisting of two parallel plates connected by a wire is slipped between the plates of the capacitor so that all four plates are parallel (Fig. 27.15B). What are the charges q1, and q2 on the plates of the I-shaped conductor? What is the potential difference VC between the top and bottom plates of the capacitor?
Car bon-zinc dry cells (sometimes referred to as non- alkaline cells) have an emf of 1.54 V, and they are produced as single cells or in various combinations to form other voltages. (a) How many 1.54-V cells are needed to make the common 9-V battery used in many small electronic devices? (b)What is the actual emf of the approximately 9-V battery? (c) Discuss how internal resistance in the series connection of cells will affect the terminal voltage of this approximately 9-V battery.
An aluminum wire 1.628 mm in diameter (14-gauge) carries a current of 3.00 amps, (a) What is the absolute value of the charge density in the wire? (b) What is the drift velocity of the electrons? (c) What would be the drift velocity if the same gauge copper were used instead of aluminum? The density of copper is 8.96 g/cm3 and thedensity of aluminum is 2.70 g/cm3. The molar mass ofaluminum is 26.98 g/mol and the molar mass of copper is 63.5 g/mol. Assume each atom of metal contributes one free electron.