of 0.12 in. (a) If the allowable shear stress is 8000 psi, determine the largest torque that can be applied safely to the tube. (b) Compute the corresponding angle of twist. Use G= 12 x 10° psi for steel.

of 0.12 in. (a) If the allowable shear stress is 8000 psi, determine the largest torque that can be applied safely to the tube. (b) Compute the corresponding angle of twist. Use G= 12 x 10° psi for steel.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The light rigid bar ABCD shown below is pinned at B and connected to two vertical rods. Assuming that the bar was initially horizontal and the rods stress-free, determine the stress in each rod after the load P = 20 kN is applied. steel L=1.5 m A=300 mm2 2 m- E= 200 GPa B D Aluminun L=2 m P = 20 kN - 1m A= 500 mm2 E= 70 GPa
A steel pipe is subjected to the 16-kN load shown below. Its outside diameter is 140 mm and its thickness is 7 mm. Consider that the yield strength of steel is 240 MPa. Analyze point H ONLY. Due to the pressure in the pipe, there is an 11.25-MPa (T) normal stress along x and a 22.50-MPa (T) normal stress along z of point H. A. Determine the internal forces and moments at the pertinent section through an FBD. B. Determine the stresses experienced by point H. Illustrate using a stress element. C. Determine the FS by MSST at point H D. Determine the von Mises equivalent stress at point H E. Determine the FS by MDET at point H 700 mm 16 KN 1,300 mm
PROBLEMS 237. The lower ends of the three bars in the figure are at the same level before the rigid homogeneous 18Mg block is attached. Each steel bar has an area of 600mm² and E=200GPa. For the bronze bar, the area is 900mm² and E-83GPa. Find the stress developed in each bar. BRONZE 1.6M STEEL 1M 18Mg STEEL 1M ТЕСНА
2. Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. What is the stress in each material given that P = 10 kN? Specify whether tension or compression. Bronze Aluminum Steel A =400 mm2 A= 600 mm2 A = 300 mm2 2P ЗР 4P P -3 m 5 m 4 m Stress in Bronze (MPa) %D Stress in Aluminum (MPa) %3D Stress in Steel (MPa)
The light rigid bar ABCD shown below is pinned at B and connected to two vertical rods. Assuming that the bar was initially horizontal and the rods stress-free, determine the stress in each rod after the load P 20 kN is applied. steel L=1.5 m A=300 mm2 E= 200 GPa Ahuminun L=2 m A= 500 mm2 E= 70 GPa 1m1m- P = 20 kN 2.
The rigid bar AB, attached to two vertical rods as shown in Fig. is horizontal before the load P is applied. Determine the maximum value for P If the stress must not exceed: 160 MPa for steel and 80 MPa for Bronze. Then determine the vertical movement of P. BRONZE L-5 m A 500 mm E-80 GPa STEEL L-4 m A-400 mm E-200 GPa 3 m. 5 m. VP
2. The bronze bar 3 m long with a cross-sectional area of 350mm2 is placed between two rigid walls. At a temperature of -20 oC, there is a gap of 2.2 mm. Find the temperature atwhich the compressive stress in the bar will be 30 MPa ifthe bar will experience:a. No tensile.b. With an tensile of 5,000 N.Use α = 18.0 x 10-6 /oC and E = 80 GPa.
A:Y 211O 2_531929016114... -> A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in Figure below. Axial loads are applied at the positions indicated. If P = 11 KN and the cross sectional area of each rod is 312.5 mm, determine the stress in each section. 4P Steel Bronze |Aluminum 609.6 mm 914.4 mm 762 mm
An aluminum bar having a cross-sectional area of 160 mm2 carries the axial loads as shown in the Figure below. Assume that the bar is suitably braced to prevent buckling and E = 70000 MPa. The length of each bars are follow: B, = 0.8 m; B, = 1.0 m; B3= 0.6 m. Determine the axial stress of bar B; in MPa. 35KN B1 B2 ВЗ ... 10KN 15KN 30KN A 218.75 B 125 C 62.5 D 31.25
A steel bar has three segments with 600 mm long which is subjected to the differentloads as shown in Figure Q1(b). Take E=205 GPa. (i) Determine stress in each section. (ii) Calculate the total elongation (extension) in the bar.(iii) Determine the length of the middle segment (BC) to have zero elongation ofbar.(iv) Determine the diameter of the segment CD to have zero elongation of the bar.
A stepped shaft is as in Figure 5-13. The AB part is aluminum (G = 28GPA) and the BC part is steel (G= 84GPA). The aluminum part has a solid circular section with a diameter of 45 mm and the steel part has a circular head section with an outer diameter of 60 mm and an inner diameter of 30 mm. Find the maximum shear stress in each material and the torsion angle at B at which the torsion moment of 4000 N.m is applied. A and C terminals are rigidly connected.
A 28mm diameter round steel bar is 0.4m long. It is placed concentrically within a brass tube which has an outside diameter of 40mm and an inside diameter of 30mm. The length of the brass tube exceeds that of the round steel bar by 0.12mm. Rigid plates are placed on the ends of the tube through which an axial compressive force is applied to the compound bar. Determine the compressive stresses in the bar and tube due to force of 60 kN. Use 200 GPa for modulus of elasticity of steel and 90 GPa for modulus of elasticity of brass.