Obtain the overall Transfer Function of the systems described by the following block diagrams. Show step-by-step simplification by performing only one reduction technique per step.

Q: Determine the transfer function using Signal flow graph.

A: Given:Block diagram of a control system, To determine: the transfer function using Signal flow…

Q: I. From the next model, obtain: a. The transfer function representation G(s) = V,(8)/V,(s). b. The…

A: First, we are going to apply Laplace transform in the below circuit.

Q: Write the state equations for the circuit given in Figure. R-12 R,=22 R532 + v=B i

A: State space equation of network

Q: The unit step sequence is defined to be the causal sequence un=1 forn20. Plot the sequences 241)…

A:

Q: Answer quickly please.

A: multiplexer comprises: Four data input lines named D0, D1, D2, and D3. Two select lines: S0 and S1.…

Q: We know that, in a monostable multi-vibrator, the application of trigger pulse gives a positive…

A:

Q: Vo Solve for the transfer function H (f) and calculate the cut-off frequency for the circuit Vs in…

A:

Q: 9. Derive the transfer function of the electrical circuit shown below. Draw a schematic diagram of…

A:

Q: G3($) CCSI てS) GCS) Gz(S) G4 CS) HIS)

A: As we have to calculate the overall transfer function of this block diagram  So we have two ways to…

Q: JA TB T KA CLK

A:

Q: High-Pass, Band-Pass and Band-Reject Filters are commonly used filters in DSP. In this task,…

A: Types of filters Band stop filter  Band pass filter  Low pass filter  High pass filter

Q: 6- Circuit analysis: Obtain a transition diagram and a state diagram for the circuit shown below. Z…

A:

Q: Find the 2-Tras form of the sequeace and Ruc

A: Given sequence: xn=13nun+12nu-n-1

Q: Using Mason's gain formula calculate the closed-loop transfer function for the system described by…

A:

Q: Reduce the block diagram to canonical form. Using the original block diagram, convert this to signal…

A: Signal Flow graph- It is graphical technique that deals with system variable that are describe in…

Q: Write a Program in MATLAB that defines and plots the piecewise signal (t) shown below in MATLAB.

A: The MATLAB code is shown in the following section:

Q: Q2): The N-bit DAC with an (R-2R) ladder network is to be designed as a 6-bit DAC device. Let (VREF=…

A: `

Q: If the noise figures of the first stage of a two stage cascade network is 8 dB and the noise figure…

A: Given; Noise figure of first stage F1=8 dB Noise figure of second stage F2=7 dB Gain of first stage…

Q: Question: Given the transfer function in figure below, Determine state space model of the system…

A: C(S)R(S)=s2+7s+2s3+9s2+26s+24=s2+7s+2(s+2)(s+3)(s+4)Doing partial fraction…

Q: circuit design for AB' + AC' + AD' + BCD

A:

Q: Vino T M3 M₂ M₁ (a) VDD Vb3 Vb2 o Vout ●Vb1

A:

Q: The serial data-input waveform (Data in) and data-select inputs (S0 and S1) are shown in Figure…

A:

Q: Q5) For the circuit shown below, find the Q- point? Vee = 20V 4.7kn 100kn B = 100 VBE = 0.7V 10kn…

A:

Q: Find the transfer functions of the circuit in figure below

A: In this question We need to determine the transfer function.  We are solving this problem using the…

Q: Q- 2: Suppose you are designing a Mathematical Calculator. You need Logarithmic and Anti logarithmic…

A:

Q: 4. In the following op-amp circuit; R=2.2 k2, R-22 kN, C₁ = C₁ 30 nF, R₁ R₂ =20 k and. The amplitude…

A: Solution- C1=C2=CR1=R2=Rfc =12πR1R2C1C2=12πRC KCL at node X,Vx-VCSC+VXR+VX-V+1SC…

Q: If the following data-input waveforms applied to the comparator, the *output in relation to the…

A:

Q: Design a counter that will output 0, 2, 1, 3 and repeat again.

A:

Q: You have a 100 mV signal in the frequency range 600 Hz to 700 Hz with which you want to drive a 200N…

A: Noise is a consistent issue in power-supply plan. While there are FCC limits on the electromagnetic…

Q: Design of op amp circuit Find the value ofC2​

A:

Q: An ................. is a circuit element characterized by the property that the current through it…

A: here as per the condition potential diffrence must be proportional to the current

Q: 4- Design a boost converter that will have an output of 60 V from a 24-V source. Design for…

A:

Q: 3) Load for a circuit with direct current source voltage The waveform of the voltage generated on it…

A: Fig: Given waveform Although it is the output voltage  wave form for single…

Q: 8 R(s) O C 0 O 1.49 E 1.65 1.25 D) 1.38 1.16 4 s(Ts+a) (a) C(s) 1 0 0.084 1.2 (b)

A:

Q: A discrete-time signal is shown in Figure below. Sketch and label carefully each of the following…

A: Signal- Signal is a physical phenomenon that contain information. Mathematically, signal is defined…

Q: For a Step-down chopper, design the circuit with 200ohm effective input resistance and 10ohm output…

A: