obtain centroid moment of inertia radius of gyration, and shear center for the L angle and channel

Q: 2.) Find also the principal stresses oi and oz and its orientations 0p1 and 0p2 from the x-axis.…

A:

Q: A thin rectangular plate is subjected to both bending and twisting. The plate is cut by an inclined…

A: Bending and Twisting Moments: Twist is the curving of a pillar under the activity of a…

Q: 0.75 m 1.5 m A B Steel Aluminum A = 250 mm? E = 200 GPa L = 2 m A = 300 mm? E = 70 GPa D Figure…

A: tanθ=∆AAO=∆BOB ∆A0.75=∆B1.5⇒∆A=∆B2

Q: calculate the location of the centroid, the second moments and product of area for the cross-…

A: The objective of this question is to calculate the location of the centroid, the second moments and…

Q: Determire the reactiors of the given beam using morment distribution method. w = 25 kN/m, P: = 25…

A:

Q: The rod ABC is made of an aluminum for which E = 70 GPa. %3D Knowing that P= 6 kN and Q = 42 kN,…

A:

Q: For the beam shown, how does the shear change as you move from A to B? B L- Select the correct…

A:

Q: For the system shown, a. Determine the equivalent force-couple system at the base at C. Express the…

A: Given:

Q: Analyze the given frame. P units in kN/m P 3m P 5m 4m pin 0.7P 4m

A:

Q: y | 1 A -X 25' 15⁰ 40° C F = 13 kips 15' B 11 .n

A:

Q: Rigid AD rod in the figure, at points A and C with two vertical ela stic bars articulated at the…

A: Using equilibrium and compatibility equations

Q: The length of 2-mm diameter steel wire CD has been adjusted so that with no load applied, a gap of…

A:

Q: ) Replace the parallel force system acting on the plate by a resultant force and specify its…

A:

Q: Problem (5) The simply supported beam AB is used to support the following loadings as shown. Weight…

A: Reactions

Q: The uniform bar with end rollers weighs 53 lb and is supported by the horizontal and vertical…

A:

Q: Determine by the method of nodes the forces at which the members EG, GF and FH, EF and ED of the…

A:

Q: GOKN A 分 年 Jom t= 200 GPa I= 100X10mmt to

A:

Q: SON AE Constant for all truss members. Solve for the horizontal 20KN displacement at joint A. 4m 2m…

A:

Q: 600 N 500 N.m 400 300 500 20

A:

Q: nto components along lines a-a’ and b-b’. 1. Determine the angle α knowing that the component along…

A: According to given data  300-lb force is to be resolved into components along lines a-a’ and b-b’.…

Q: An axial member consisting of two polymer bars is supported at modulus of 29 GPa. Bar (2) has a…

A:

Q: Solve for: 3) RA Ro 6) MA

A:

Q: A beam is subjected to equal bending noments of M, = 2700 N-m. The cross-sectional dimensions are b=…

A:

Q: Problem 2. The homogeneous wire ABCD is bent as shown and is attached to a hinge at C. Determine the…

A: Given:- To find:- Length L

Q: Three cables pull on the pipe such that they create a resultant force R. Two of the cables are…

A:

Q: The divergence of a vector field F(x,y.z) = xyři + 2x²yzj – 3yz'k at the point (1, -1,1) is 9. -3 3…

A: Option a (i.e 9) is correct answer

Q: A cylindrical pin made of carbon steel is loaded with a maximum possible twisting moment Mv. Maximum…

A: G = 80 GPa  Maximum shear stress = 40 MPa  Determine the free end distortion in degree.

Q: A зоки/т Чт ще

A:

Q: Eхаmple (1) The direction of the force (P) is (30° components is (30N). ina find the horizontal…

A: Step 1

Q: Problem 2-A concentrated couple, Mo = 600 Nm acts at the center of the simply Supported beam which…

A:

Q: A symmetrical beam of length 300 mm is loaded with a force of 414 N downwards (positive z) and has…

A: Given: The vertical displacement is given by, wx=FEIyx448-L2x28+L42 The modulus of elasticity is…

Q: The L-shaped arm ABCD shown in the figurelies in a vertical plane and pivots about a horizontalpin…

A: Given:- L-shaped arm ABCD  To find:- (a) Obtain a formula for the elongation of the spring due to…

Q: The pin at C is with a diameter C. Assume that the pin at C is supported as stated in the table.…

A:

Q: A. The resultant of the four belt tensions and couple C is force R acting through points O. 1. What…

A: Moment about OMO=1000(0.45)+200(0.3)-800(0.3)-400(0.45)Mo=C=90 N-m

Q: The curved member is made from a material having allowable bending stress of sallow = 100 MPa.…

A:

Q: B 0.9 M 900 N 0.6 M 2.4 m A.

A:

Q: The uniform rectangular panel ABCD has a mass of 40 kg and is hinged at its corners A and B to the…

A:

Q: A symmetrical beam cross section is shown below. The centroid is in the exact centre of the section.…

A:

Q: H V b a-The internal shear force V at a certain section of a beam is 60 kN.m. If the beam has a…

A:

Q: a. Axial force on member ED from the real structure in kN. Put (-) negative sign if it's under…

A: Given Data: A truss of A=1200 mm2,  E=200 Gpa α=12*106 /°C  It is asked to find axial force in…

Open Channel Flow

Open channel flow is a branch of fluid mechanics. It deals with the flow of fluid in an open conduit or free surface. In an open channel flow, gravity induces the flow of water whose surface is open to the air. This flow is free-falling rather than confined in rigid body conduits. The open channel flow depends upon two parameters that are the cross-section of the conduit and the velocity profile. Practical examples of open channel flow are streams, rivers, canals, and other drainage systems.In open channel flow, the cross-sectional area of at least one of the sides is exposed to air, and the surface of water faces atmospheric pressure. This flow is also known as free gravity flow. The cross-sectional area of the conduit can be either man-made or a natural channel. For instance, the flow in rivers and streams are natural conduits, and the flow in a canal and sanitary systems are man-made or engineered channels.