O O O O in 4 in.3 in 2 in. 4 in. 4 in. 21 2 in. 12 in.

Q: -5 @ 3m-15m- C F H J K ML boo I A 4@4m=16m B D G E 60 kips A For the truss shown, what is the force…

A:

Q: Determine the smallest safe cross-sectional areas of members CD, CI and CH for the truss shown. The…

A:

Q: Two plates are joined by four bolts of d=20-mm diameter, as shown in the figure. The shearing stress…

A: We have to determine the value of maximum load P as the shearing stress is limited to 70 MPa,…

Q: For the truss shown below, F= 12 kN and L= 3 m. a) Determine the force in member BE. A and E are…

A:

Q: 50 000 N Prob. 2-4 25 000 N Internal Force of Member AG 2. AG = 20 m B 10 m E G F 20 m 20 m 20 m

A: Given data in question  Point loads vertical and horizontal  Span member length  To find out  FBD…

Q: Check the stability of truss.. Give me right solution with clear calculations.

A:

Q: 8 kN/m 35° E By D 20 kN 0.4 m 0.4 m 0.4 m

A:

Q: 1. Is this truss (simple, compound or complex )truss? 2. Determine the bar force in member AF of the…

A:

Q: 10 KN 15 KN 10 KN E 0.9 m 0.9m A G B IF 1.2m 1.2m 1.2m C.

A:

Q: Determine the type and amount of stress in each member of the truss shown below due to wind load…

A:

Q: 4.Calculate and determine the nature of the forces in the bar EF,FC ,and BC with ritter cut method

A: Hint: Height of F = 3 tan30°=1.73 m         φ=tan-11.731=59.97° ∑MA=0-RD×6 + 30×4 +…

Q: a. Assuming all the members have the same properties (E=29,000 ksi, A = 4 in?, Fy = 36 ksi) what is…

A:

Q: the

A: A device for measuring corneal thickness that is installed on a slit-lamp is known as pachometer. It…

Q: Find the Zero- Force Members at the shape: D. L M 10n 10 t 10 A 10 A 10A 10t 10A 6 kips kups 6 kips…

A:

Q: 15 Flad the ABE GO Kri CD = 70 ksi BC - 50 ksi 0.4 in2 4. 0.3 n? 4P- 3p P4

A:

Q: Find internal force of members DE , NE , NM use section method

A:

Q: Determine the type and amount of stress in each member of the truss shown below due to wind load…

A:

Q: 02. The member consists of the steel rod AB that is screwed into the end of the bronze rod BC. Find…

A: Apply deflection condition i.e PL/AE. Where P is load

Q: föllowing SS is subjected to diameter mm and is subjected to double shear. Determine the average…

A: Consider the diagram as shown below.

Q: Calculate 'the force in each member of the loaded truss. All triangles are isosceles. Indicate…

A:

Q: solve the stresses in members DF,DG and EG using method of sections

A: Given data  Using method of section

Q: Try to write out the stress boundary conditions of the cantilever beam. ( not include the fixed…

A: Three force are there on cantilever beam   F force, UVL load and q force.....

Q: DIRECTION: Solve and Analyze the following problems in neat and orderly manner. Use your indicated…

A: Determine the force in each member of the truss and state if the members are in tension or…

Q: Determine the normal stress in members DF, GH, and GI in the truss shown. The cross-sectional area…

A: Given data Truss with loads.  Area, A = 900 mm2 To find Stres in the mentioned member.

Q: Draw FBD, and all necessary sketches.  b. Find the reactions and the stresses in all the members of…

A:

Q: 4 m B P₁ 4 m C₁ 4 m 6 m D

A: Identify the Reaction of Truss support  Apply Equilbrium Condition to get the Reaction. Then apply…

Q: K 5' El constant 10 ft 5' 10 k-ft 10 ft 10 k-ft

A: To solve the problem using stiffness methodP= 95 k

Q: Link AB is to be made of steel for which the normal stress is 450 MPa. Determine the cross-sectional…

A:

Q: B C 2 m A G. -2 m- -2 m- -2 m- 1000 N e the truss from Problem #1below to determine the force in…

A: Solution  Initially find the reactions and consider  Each joint individually and use equilibrium…

Q: II. Determine the force in members BF and EF using: a) Method of Joints b). Method of sections. 3…

A:

Q: Determine the normal stress in members BD, AC, and BCin the truss shown. The cross-sectional area of…

A:

Q: Usinf the method of sections, determine the force members GF, GD, and GC

A: Take moment about A:∑ MA=0Ey8-46-74-102=0Ey=9kN

Q: The members of the truss are 25mmx50mm in cross section. Determine the maximum load P that can be…

A: To calculate the value of P we have to find the forces in the members using the method of joints…

Q: sider the truss shown in (Figure 1). Set P₁ = 8 kN, = 10 kN, and P36 kN. re P₁ -3 m P₁ 3m P₂ 3m- 1…

A:

Q: 1-45. The truss is made from three pin-connected members having the cross-sectional areas shown in…

A: Given Data : Determine the average normal stress developed in each member when the truss is…

Pressure and Stress