nj. A beam is 10.5 m in length and loaded as shown in Figure Q4. If the deflection in the mid-distance between A and B is 3 mm, find the value of flexural rigidity (El). Find also the value and location of the maximum deflection. 3 kN C 2.5 m A 1 kN/m [[|] 6 m ding B 1 kN 2 m D

nj. A beam is 10.5 m in length and loaded as shown in Figure Q4. If the deflection in the mid-distance between A and B is 3 mm, find the value of flexural rigidity (El). Find also the value and location of the maximum deflection. 3 kN C 2.5 m A 1 kN/m [[|] 6 m ding B 1 kN 2 m D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Problem 2: A circular tank of 3.91m in diameter is uniformly loaded with 100 kPa. Compute: a) The…

A: Given:- The diameter of the circular tank = 3.91 m The magnitude of the uniformly loaded tank = 100…

Q: 3 d²y dx² dy -2 -8y = 0 dx

Q: need asap please

Q: Question - A round about is provided with an ung entry with. Ding Of 8.4m width of weaving section…

Q: A 200-acre urban drainage area consists of three different watershed areas: 60% single-family, 30%…

Q: 10. Find the stresses in member BC, BD and CF for the truss shown in Figure 8. Indicate tension or…

Q: The support reaction at the base of the spring, the rotation of the beam at the left support.

Q: Fluid flows into a junction at a flowrate Q, and exits via two pipes of equal diameter, as shown in…

Q: The compression curve (void ratio, e vs. effective stress, o) for a certain clayey soil is a…

Q: For the given beam, draw the simplified free-body diagram and below it the shear and bending moment…

Q: 9:33 PM Parts Answers: A, Part 2 Use the graphical method to construct the shear-force and…

A: Solution: Part 1: Taking moment about A: Cy×17=5.5×12×122Cy=23.29 kipsAy+Cy=66…

Q: QUESTION 1: Determine the force acting on member GC. A 5 kN 3 m 2 kN 5 kN -2 m- B -2 m- C 2 m- 5 kN…

A: Given data

Q: Determine the percent reduction n in the polar moment of inertia of the square plate due to the…

Q: solving

Q: Q.1 Determine the reaction at supports and the force in AB, BC, and BD members of and indicate…

Q: Determine the maximum force P

Q: Q2/ A cylindrical barrier holds water, as shown in Fig.1, the contact between cylinder and the wall…

Q: Indian Standard (IS) Light Compaction test is usually conducted in 3 layers in a 1000 cc mould. How…

A: Given- IS Light Compaction Test- 3 layers in 1000 cc mouldfor 2250 cc mould number of blows per…

Q: The steel channel is used to reinforce the wood beam. Determine the maximum stress in the steel and…

Q: Need complete solutions. Box the final answers. AWT305 x 41 standard steel shape is used to support…

A: Given data

Q: I did not pay the subscription amount in order for my questions to be rejected!!! Please I need…

A: Solution: Given: Column Span = 3.3 m fck = 30.5 MPa fy = 472 MPa DL = 3.55 kPa LL = 4.55 kPa

Q: e moment distribution method to determine the moments at B and C.

Q: Solve for the velocity of car B and the angle 8. Answers: VB = B 0= = V i i + V C V BIC VC B/C…

Q: 2. The data tabulated represents earthwork quantities for a certain road extension project. STATION…

Q: A rectangular beam is 24 in. wide. The architect asked for this beam to have a maximum depth of 16…

A: Answer : We are given Width b =24 in Maximum depth h = 16 in Ultimate Moment Mu = 400 Kip-ft…

Q: The mean dimensions of the cross section of the leading edge and torsion box of an airplane wing can…

Q: The moments of inertia of the area A about the parallel p- and p'-axes differ by 69 in.4 Compute the…

Q: A road section to be laid out passes through a hilly terrain illustrated below. The section in fill…

Q: Who performed an experiments to study the effects of loads on rods and beams made of various…

A: Leonardo da Vinci performed possible tests of tensile strength on a wire Later Galileo Galilei…

Q: Q. In the offshore region at a particular harbour facility, an oscillatory wave train approaches…

A: Given- Wavelength L=80 mMean sea depth h=30 m

Q: Determine the design axial and moment capacity at eccentricity of 350 mm.

Q: The cross-sectional dimensions of a beam are shown. Assume b=2.5 in., t-tw-0.375 in. and d=3 in. (a)…

Q: 16. Which of the following is/are correct? 1. Clays are generally compacted by Vibratory rollers II.…

A: This question is related to the Soil Mechanics from Civil Engineering. I solved all three questions…

Q: Solve for the reactions and all the member forces directly on the truss members. Use method of…

A: Given data:

Q: Two blocks A and B of the same mass 1.11 kg are released from rest on a 28° incline when they are S…

Q: If the elastic modulus and the Poisson's ratio of the clay layer are respectively 50 x 10³ kPa and…

A: Solution:-The given data is,The clay layer ,The elastic modulus (E)=50×103kPAThe poision…

Q: A trapezoidal channel is to be designed to convey a discharge of 50 m³/sec at a velocity of 2 m/sec.…

A: GivenTrapezoidal channel-Discharge Q=50 m3/sVelocity V=2 m/sbed width to depth ratio-By=0.8side…

Q: 4. Find the maximum allowable value of P for the column. The cross- sectional areas and working…

Q: A steel [E = 30,900 ksi; a = 6.2 x 10-6/°F] pipe column (1) with a cross-sectional area of A₁1 =…

Q: Segment A of the composite beam is made from 2014-T6 aluminum alloy and segment B is A-36 steel. If…

A: Given :

Q: 4- List and explain factors that affecting the setting of Portland cement. un

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: A 3-kg disk A is mounted on arm BC, which has a negligible mass. A torque of M (5e0.5t) N-m, where t…

A: Given data:- The given disk weight is, w=3 kg The given thickness of the disk, t=60 mm The given…

Q: The truss supported by a pin at D and a roller at A, is subjected to the vertical load as shown.…

A: Given :

Q: the ultimate consolidation ent (expressed in mm) of the clay

Q: At an impaired driver checkpoint, the time required to conduct the impairment test varies…

Q: Q3): The following data were collected while running a closed traverse ABCDA. Calculate: 1-…

A: Solution-For Multipart questions as per the policy only three parts can be solved for other parts…

Q: ual measurement

A: We knowLtrue=lwrongltrueLwrongLtrue=True length of lineltrue=True length of ltapeLwrong=wrong length…

Q: A stone is dropped from a captive balloon at an elevation of 1000 ft. Two seconds later, another…

A: Solution-The given values are as follows,The elevation=1000ftThe velocity=248ft/sTo Determine At…

Q: On a steel bar specimen of 15 mm diameter and 150 mm gauge length, when tested as a tensile test…

A: Given- diameter of bar d=15 mmgauge length L=150 mmfor tensile test-Force F=15 kNextension=0.063…

Q: Part A An aluminum 2014-T4 alloy bar 2.50 inches wide and 0.750 inches in thickness has a 1/4 inch…

A: Given,P=8650 lbsb=2.5 int=0.75 inr=14 in=0.25 inσmax=7670 psi

Concept explainers

Beams

In structural engineering, a beam is a component made of a variety of materials (including steel alloys, and wood) that can resist loads applied laterally to the beam axis. Members, elements, rafters, shafts, and purlins are all terms used to describe beams.

Question

nj. A beam is 10.5 m in length and loaded as shown in Figure Q4. If the deflection
in the mid-distance between A and B is 3 mm, find the value of flexural rigidity (El). Find also the
value and location of the maximum deflection.
3 kN
.-.-
C
2.5 m
1 kN/m
| || | || | ||
A
6 m
mussenbo
Figure Q4: Beam Loading
B
1 kN
2 m
D

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step by step

Solved in 6 steps with 13 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

From the given beam shown. Determine the deflection at the free end. Use Double Integration. Let P-23 kip, L-18 ft. 3200 in?, E 29000Ksi %3D Note: 1. Indicate the negative sign. 2. Answer in 4 decimal places 3.. for FBD (properly labeled) (answer should be correct too) 4. . for the solution P. L.
Determine the following unknowns on the beam shown below using Conjugate-Beam Method. Consider 250 mm x250 mm section and E = 200 GPa. Show complete and organized solution. a. Vertical Reaction at C in kN. b. Moment Reaction at C in kN-m. c. Deflection at point B in mm. d. Maximum deflection on the beam in mm Given: a- 4m b- 24kN/m c- 9kN
The beam with, cross-section shown, is subjected to the load shown. Using E-200 GPa, determine a. the value of Ely at B and D b. the deflection at B and D 80 mm ► 4 kN/m 16 KN 25 mm B D 6m 4m 2m Using Moment-Area Method 25 mm 140 mm I 25 mm 120 mm
Q2) For the beam loaded as shown determine the deflection at the free end, and the beam rotation at the left support. Take EI= 860 kN.m². 15KN 10KN/m 30KN.m R1=33KN Im 3m Im Im R2=12KN
In the restrained beam shown, solve for the following a. end moments b. max deflection note: use double integration method 3 kN /m 15KN 1m マク Im
The beam with, cross-section shown, is subjected to the load shown. Using E-200 GPa, determine a. the value of Ely at B and D b. the deflection at B and D 80 mm 25 mm 4 kN/m 16 KN B 6m 4m C 2m D 140 mm 25 mm 25 mm 120 mm
The simply supported beam A' of length L carries a concentrated load P at midspan. Another beam 'B' is loaded with a uniformly distributed load such that the total load on the beam is P. Calculate the ratio of maximum deflections between beams A and B. OA 5/8 O B. 5/4 OC.4/5 O D. 8/5
Determine the following unknowns on the beam shown below using Area-Moment Method. Consider 150 mm x150 mm section and E = 80 GPa. Show complete and organized solution. a. Vertical Reaction at B in kN. b.Moment Reaction at A in kN-m. c. Deflection at point C in mm. d. Deflection at midspan of AB in mm. Given: a- 7m b- 24kN/m C- 30kN
ACTIVITY 3- Beam Analysis Analyze the loaded beam as shown. Be guided as follows: a. Solve for the reactions at supports b. Draw Shear and Moment Diagrams C. Compute for deflection at A (AA) and slope at C (0c) using Conjugate Beam Method 50 kN 90 kN ↓ B A JAUME |-6: 6 m 9 m El = constant E = 70 GPa I=95 (106) mm4 -9 m
Moment-Area Method 1. Compute the value of the following for the beam shown: (El is constant.) a. Slope A b. Slope Oc 10 KN .0.50 kN/m IMI B C 1.5 m 1.5 m1m C. Deflection Ac d. Deflection AE e. Maximum deflection between support A 1.5 m- D 10 KN E
A 6KN/m 5m 5m 5m El-Constant Analyze the beam using Slope Deflection Method Draw shear, bending moment and elastic diagrams 6KN/m 5m E
1. A horizontal simply-supported beam is loaded as shown in Figure 1. It has a rectangular cross section, 70 mm by b mm. (a) Determine the vertical reaction forces at A and E. (b) If the allowable deflection at mid-span is 2 mm downwards, determine the dimension, b, of the beam needed. Use E= 150 GPa. 10kN 6kN/m 4kNm [36.26mm] Section A-A of Beam AF 0.2m 0.3m 0.8m E olo 水水 0.2m 0.3m 3kN Figure 1