Nine-pile group consist of 0.33-meter-diameter friction concrete piles 21 m long arranged in 3 rows by 3 columns. The piles are driven into clay having unconfined compressive strength of 116 kpa. Tha spacing of piles 0.67 m. on-center. Adhesion factor of the piles is a=0.64. Determine the allowable block capacity (inKN) of the pile group based on the arrangement described. Use FS = 2.78

Nine-pile group consist of 0.33-meter-diameter friction concrete piles 21 m long arranged in 3 rows by 3 columns. The piles are driven into clay having unconfined compressive strength of 116 kpa. Tha spacing of piles 0.67 m. on-center. Adhesion factor of the piles is a=0.64. Determine the allowable block capacity (inKN) of the pile group based on the arrangement described. Use FS = 2.78

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

sw
Q2: The plan of a group piles is shown below. Assume that the piles are embedded in a saturated homogeneous clay having a 7sa= 19.24 kN/m, C=41.2 kN/m? .Given: diameter of piles (D) = 305 mm, center-to-center spacing of piles 762 mm, and length of piles = 13.7 m. Find the allowable load-carrying capacity of the pile group. Use FS = 3. P
Q1/ For the footing shown in Figure (1), estimate the pile group capacity. 0.6m dia bored pile Clay c=80 kN/m² y-17kN/m² S=1.5 m T L=12 m
Q1: Determine the allowable load capacity for the driven pile of 0.6 m diameter embedded in a layered soil as shown in the figure below, use F.S 2.0 , K, = 1.5 and tand =0.5? ELEV. 110 N.C.C W.T ELEV. 108 Cu =70 kPa Y = 17 kN/m3 a = 1, yw = 10 kN/m? ELEV. 102 O.C.C, Cu 180 kPa, y = 20 kN/m³ a = 0.45 ELEV. 98 Sandy Layer Yt = 19 kN/m3 Ø = 32° Nq = 23.18 ELEV. 90
A group of 9 piles of 29 cm diameter is arranged in a square configuration with a center-to-center spacing of 1.01 m. The length of the piles is 12 m. Unit cohesion of the clay is 80 kPa. Determine the ultimate group capacity of the pile group based on block failure. Assume adhesion factor of 0.69.
A rectangular pile (0.85 x 0.77) is driven in clayey soil arrangement composed of two different layers. First laye has a height of 9 m., cohesion of 59 kPA, friction factor of 0.84. Second Layer has a height of 5m., cohesion of 74 kPa, and friction factor of 0.87. Compute the allowable load that the pile can carry if the factor safety is 2.37. Use stored value. Answer to 5 decimal places.
Nine-pile group consist of 0.21-meter-diameter friction concrete piles 24 m long arranged in 3 rows by 3 columns. The piles are driven into clay having unconfined compressive strength of 100 kPa. The spacing of piles is 0.66 m. on-center. Adhesion factor of the piles is α = 0.77. Determine the allowable block capacity (in kN) of the piile group based on the arrangement described. Use FS = 3.33.
Nine-pile group consist of 0.37-meter-diameter friction concrete piles 20 m long arranged in 3 rows by 3 columns. The piles are driven into clay having unconfined compressive strength of 121 kPa. The spacing of piles is 0.68 m. on-center. Adhesion factor of the piles is a = 0.78. Determine the allowable block capacity (in kN) of the piile group based on the arrangement described. Use FS = 3.49. Round off to two decimal places.
Check the total settlement of a group of pile as shown in Figure 1. The total allowable settlement is set not exceed 3% of the pile diameter and the overconsolidated ratio (OCR) of the clay is more than 1. The groundwater table is located 15m beneath the ground level. The diameter of the pile, b is 0.5m and the spacing between piles, s is 2m.The pile group is subjected to foundation load of 5425kN. The laboratory testing data for the soil samples taken are as follows: At 5m, eo = 0.55, Cc = 0.32, C; = 0.09, o'o = 150kN/m? At 10m, eo = 0.55, Cc = 0.32, Cs = 0.09, o'o = 225kN/m2 %3D At 12m, eo = 0.55, Cc = 0.32, C; = 0.09, o'o = 300KN/m2 %3D 7m 5m Clay 3 10m Unit weight = 18KN/m %3D Friction angle = 0 degree 2 Cohesion = 100KN/m
A group of 16 piles of 50 cm diameter in arranged with a centry to centre sporing of 1.0 m. The piles are 9 m long and are embedded in soft stay with cohesion 30kN / (m^5) Bearing resistance may be neglected for the piles-Adhesion factor is 0.6. Determine the ulti mate Load capacity of the pile group.
Solve it asap plea