For the beam shown, do the following:1. Determine the values of shear at every change of load points by the AreaMethod and mark the maximum value.2. Determine the values of moment at every change of load points by the AreaMethod and mark the maximum value.3. What is the moment at a point 3m from the left end?4. What is the slope of the shear diagram at the exact point C?5. Draw the elastic diagram.All lengths are in meters. There is a pin at Point B and fixed support at A..jokulmB2m

As there are multiple questions posted, according to the guidelines, only the first three are being…

n, do the 1. Determine the values of shear at every change of load points by the Are Method and mark the maximum value. 2. Determine the values of moment at every change of load points by the Are Method and mark the maximum value. 3. What is the moment at a point 3m from the left end? 4. What is the slope of the shear diagram at the exact point C? 5. Draw the elastic diagram. All lengths are in meters. There is a pin at Point B and fixed support at A.. 10144/m j0kulm

n, do the 1. Determine the values of shear at every change of load points by the Are Method and mark the maximum value. 2. Determine the values of moment at every change of load points by the Are Method and mark the maximum value. 3. What is the moment at a point 3m from the left end? 4. What is the slope of the shear diagram at the exact point C? 5. Draw the elastic diagram. All lengths are in meters. There is a pin at Point B and fixed support at A.. 10144/m j0kulm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Completely solve. WRITE LEGIBLY OR TYPEWRITE THE SOLUTIONS. BOX THE FINAL ANSWER.
The shaft has a radius of 15 mm and is made of L2 tool steel. Determine the strains in the x and y direction if a torque T = 2 kN # m is applied to the shaft.
Please show complete solution and draw the diagram
Show step by step
This is easy one ,Please make it short and simple. There are few solution available which are lengthy.
A simple torsion-bar spring is shown. The shear stress in the steel [G= 11,500 ksi] shaft is not to exceed 8800 psi, and the vertical deflection of joint D is not to exceed 0.400 in. when a load of P = 3000 lb is applied. Neglect the bending of the shaft and assume that the bearing at C allows the shaft to rotate freely. Determine the minimum diameter required for the shaft. Use dimensions of a = 70 in., b = 24 in., and c = 24 in. a b Answer: d= D P B in. C
help find the stress at segment BC, please
3 mm- 4. The cross section of the steel tube (G = 11 x 106) as shown carries a 50 kip-in torque. Calculate (a) the maximum shear stress and (b) the angle of twist per foot of length. Use 2 decimal places in every solved value. mm 2mm mm 3 mm mm- 8 2 of 2
Q3/ The three forces and the couple are applied to the bracket shown in Figure below. Determine (1) The resultant of the force system. (2) The points where the .resultant cuts the line (AB) and (BC) 125N SON 300 mm YY+ M=8 N.m 2. 200 N
A simple torsion-bar spring is shown. The shear stress in the steel [G= 11,500 ksi] shaft is not to exceed 12000 psi, and the vertical deflection of joint D is not to exceed 0.600 in. when a load of P = 3700 lb is applied. Neglect the bending of the shaft and assume that the bearing at C allows the shaft to rotate freely. Determine the minimum diameter required for the shaft. Use dimensions of a = 84 in., b = 22 in., and c = 32 in. a b Answer: d = B in.
A. Calculate the shear force in the pin at B in pounds. B. Calculate the shear stress in the pin at B in psi.
Ql:- The system of gears B and C take out power 150 and 175 hp respectively from a motor A that has 325hp, Find the shaft dimeter if the allowable shear stress is 6250 psi and the angle of twist between gear C and motor is 2 degree. Let G=11.5 x 10° psi. Gear Gear Motor A B