mustrate, label and Solve the problem Delow. Problem: The angle of depression of boat A from the top of a cliff which is 24"15'. The angle of depression of boat B from the same point is 18" 12". Find the distance between the two boats.
Q: a) Set up but do not compute the integral for the volume of the solid below using cross-sectional…
A:
Q: Questions and Problems Q2 State the number of significant figures in each of the following…
A: Since you have posted multiple questions we will solve the first question for you. If you want any…
Q: how do i slove?
A:
Q: A screw gauge advances by 3 mm on main scale in 6 rotations. There are 50 divisions on circular…
A: A screw gauge advances by 3 mm on main scale in 6 rotations. There are 50 divisions on circular…
Q: Which tool would be best to use for measuring the following: a) Diameter of a wire. Explain. b)…
A: a) A screw gauge would be better to measure the diameter of a wire because it's least count is…
Q: A Vernier caliper has 50 divisions in the Vernier scale. What is the Vernier scale reading if the…
A: Given data n=50 Here, n is the number of divisions on the main scale. Now we have to find out the…
Q: 7. Which instrument is used to measure the volume of an irregular shaped object ? C. a micrometer…
A: Asked: Instrument used to measure volume of irregular shaped objects.
Q: 1) Using dimensional equations, convert: 700 m /(day. kg) to cm' /(min. g). 2) Convert 210X 10°…
A: Note:- Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the…
Q: A block of mass 5.5 kg is suspended from two vertical ropes attached to the ceiling. What is the…
A:
Q: ELABORATE The areas is cut of 2 irregular sections 35m apart are 34 sq.mtrs and 56 sq.mtrs the base…
A: To answer: Find the volume of cutting using prismoidal rule
Q: What is the smallest reading a vernier caliper can have if it has 20 divisions in the vernier scale?…
A: Let N be the number of the division which I s present in the vernier scale. Given that…
Q: -55. Locate the center of gravity (..) of Omogeneous wire. 300 mm 400 mm
A: length for segments 1 and 2 are find using pythagoros theorumand length of segment 3 is find by…
Q: 3-Drive a formula for the worst and standard errors in the total surface area of closed cylinder…
A: Drive a formula for the worst and standard errors in the total surface area of a closed cylinder…
Q: Least count of a vernier callipers is 0.01cm. When the two jaws of the instrument touch each other…
A: The correct answer is A. The diameter of sphere is 2.51 cm.
Q: 3. Now suppose the length and diameter of the cork were measured. Archimedes' principle was used to…
A: Archimedes’ principle is very beneficial for calculating the volume of an object that does not have…
Q: The volume of a cylinder is given by V= Tth, where ris the radius of the cylinder and h is the…
A: The variance in the product of N independent variables is given by VarX1X2X3...XN=∏i=1Nσi2+μi2 -…
Q: What is the area of the object shown above? (include units with answer) A. What is the X coordinate…
A:
Q: You have an aquarium which holds 9.45 gallons of water and you would like to place it on an antique…
A:
Q: Given data : Mass = 36 kg Density = 670 kg / m3 Determine the volume
A:
Q: Determine the height h above the base of the centroid of the cross-sectional area of the beam.…
A: Solution: As per the above-given figure, It can be redrawn as follows:
Q: Pipe ti of 0.8m. WI and adjacent 10. The longes What is the lo the pipe is (a)
A: Given data: The length of pipe with one end closed is: L = 0.8 m The distance between a node and…
Q: Use Desmos to graph the function, then answer the following questions. a) What is the maximum height…
A: Given information: Equation of the bridge: y=-0.00188x2+0.946x-49 The graph in Desmos is:
Q: Claws cd measures ________ A. Inside diameter B. Outside diameter C. Depth D. None of these
A: Given: A vernier caliper
Q: question in the picture
A: Given:The width of the hallway is 3 foot. Introduction: The maximum area of the rectangular couch…
Q: 5. Find the Mass of wateY 1oquired to fill pol lof length 100cm,bieadth 40cm and depth 0em
A: Given Length l=100cm Breadth b=40cm Depth h=30cm Density of water ρ=1g/cm3
Q: Determine the Cross-sectional Area and Volume of Cylindrical Object Measure diameter with a…
A: Given that, the pitch scale reading is P.S.R=12mm Circular scale reading is C.S.R=22 Least count is…
Q: QUESTION 12 Protractor is used for Angular mesurement True False QUESTION 13 Pallet hammers are used…
A: Protractor is used to measure plane angles. Answer: Yes
Q: Choose correct dimensional equation to stress. [Hint: Stress = Force/Area] O a. M°L'T? O b. M'L"T -2…
A: Introduction: The stress of the object is defined as the resistive force per unit area, which is…
Q: h One end of a ladder of length L rests on the ground and the other end rests on the top of a wall…
A: The diagram for the problem is given below.Let us consider that ED = h', CE = y, AC = L-yAs, AE = L,…
Q: DRAW THE PROFILE OF AROTATING SQUARE PALTE OF 120mm SIDE FOLLOWED BY AFOLLOWER.
A: To draw the a rotating square plate with the side of 120 mm is drawn below.
Step by step
Solved in 2 steps with 1 images