Answered: mplify the block diagram shown in…

Engineering

Electrical Engineering

mplify the block diagram shown in following figure and obtain the closed-loop ansfer function C(s)/R(s).

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Design an op-amp circuit that meets the following specifications. Your design can be done with one or two op-amps. Your instructor may give you a different design. Note: Show all work. Draw a schematic of your design and label component values and op-amp pin numbers. a. The op-amp circuit must have a non-inverting overall voltage gain that is adjustable from +3 to +12. The circuit has a 47 k load resistor connected from the last op-amp's output terminal to ground. b. c. The circuit input resistance must be ≥ 50 kn. Your design is limited to a maximum of two op-amps and seven resistors, one of which is a variable 100 k resistor (potentiometer). The potentiometer resistance is 0 22 when adjusted to one extreme of its range and 100 k at the other extreme. d. When the potentiometer is adjusted to one extreme position the overall circuit voltage gain should be +3. When the variable resistor is adjusted to its other extreme position the overall circuit voltage gain should be +12.
Discuss comparator with its voltage transfer charcateristic.
Electrical Engineering With an op amp design a square wave oscillator at ± 3 volts with a frequency at 20 kHz. Draw the schematic of the square wave oscillator. Write the formulas that is using for the design and the values of the resistors and capacitors that are needed to get the requested frequency.
1. Given that the input V1(t) in Figure 4 (a) is a 3V peak triangle wave at 4 kHz.Answer the following 2.The circuit in Figure 4 (b) has 5 op-amps labeled as U1 through U5. State what the op-amp circuit is for U1 Circuit: U2 Circuit: U3 Circuit: U4 Circuit: U5 Circuit: 3. Determine the values of VO1, VO2, VO3, VO4 and VO5. 4. Draw the output waveform at VO5 for the given input waveform shown in Figure 4 (a).
a circuit design for AB' + AC' + AD' + BCD Thank you!
4
TRUE/FALSE QUIZ Answers can be found at www.pearsonhighered.com/floyd. 1. An ideal op-amp has an infinite input impedance. 2. An ideal op-amp has a very high output impedance. 3. The op-amp can operate in both the differential mode or the common mode. 4. Common-mode rejection means that a signal appearing on both inputs is effectively cancelled. 5. CMRR stands for common-mode rejection reference. 6. Slew rate determines how fast the output can change in response to a step input. 7. Negative feedback reduces the gain of an op-amp from its open-loop value. 8. Negative feedback reduces the bandwidth of an op-amp from its open-loop value. 9. A noninverting amplifier uses negative feedback. 10. The gain of a voltage-follower is very high. 11. Negative feedback affects the input and output impedances of an op-amp. 12. A compensated op-amp has a gain roll-off of -20 dB/decade above the critical frequency. 13. The gain-bandwidth product equals the unity-gain frequency. 14. If the feedback…
Please read the instruction of the first picture and analyze it or just do what is left. The second picture has my work and the circuit. Can you finish the other requirements that would be great and appreciated.
Consider the circuit shown in the figure below. The figure consists of an ideal op-amp circuit. The transfer characteristics of the circuit can be represented as R, D, 7 R, ww D2 2R2 -15 V
Create Op-amp circuit... with:Vin= -1 Volt (DC) Vout = 14 Volt (DC) Only resistors with 1k, 3k, 5k, 7k and 11k ohms can be used while the circuit is being built. The V+ value of the LM741 IC to be used for op-amps will be 20 volts and the V- value will be -20 volts. You need to use at least one inverting amplifier and one non-inverting amplifier to build the circuit. Question: Write the gain formula of the circuit and calculate it, and write how we should find the Vout value..
Please show all work
Using Table P.1, For the following figure 4 if R1 = 1000 and VIN = 1V answer the following questions: +Vee VIN υουT Vee ww. R2 R1 GND Fig. p.4 a) What is the fig.4 circuit name? b) In fig.7 if R2 = 4000, determine the Gain K? Show all steps c) In fig.7 if R2 = 4000, determine the VOUT? Show all steps d) In fig.7 if VOUT = 6V, determine the R2? Show all steps