Motion of the wheel as it rolls up the fixed rack on its geared hub is controlled through the peripheral cable by the driving wheel D, which turns counter- clockwise at the constant rate wo = 4 rad/s for a short interval of motion. By examining the geometry of a small (differential) rotation of line AOCB as it pivots momentarily about the contact point C, deter- mine the angular velocity w of the wheel and the ve- locities of point A and the center 0. Also find the acceleration of point C. show complete solution show free-body diagram

Motion of the wheel as it rolls up the fixed rack on its geared hub is controlled through the peripheral cable by the driving wheel D, which turns counter- clockwise at the constant rate wo = 4 rad/s for a short interval of motion. By examining the geometry of a small (differential) rotation of line AOCB as it pivots momentarily about the contact point C, deter- mine the angular velocity w of the wheel and the ve- locities of point A and the center 0. Also find the acceleration of point C. show complete solution show free-body diagram

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A piston slider crank mechanism is shown beolow. The connecting rod having a length of 1125 mm enables the rotational motion generated by the crank with a diameter of 500 mm to the transnational motion of the piston The crank is turning at 410 rpm At the given instant shown, find the angular velocity of the connecting rod when the angle of the crank is 59* from the horizontal axis. Crank Connecting Rod Piston Cylinder
The disk has an angular velocity of 8 rad/s and is increasing at the rate of 5 rad/s' about its Z- axis and the yoke AB has a constant angular velocity w = 3 rad/s about its shaft as shown. Simultaneously the entire assembly revolves about the fixed X-axis with constant velocity o, = 5 rad/s. Determine the velocity and acceleration of point F on the disc for an instant shown in the figure. Also find angular velocity and angular acceleration of the disc. 20 cm 15. 30 cm 30 cm 30 cm N 20 cm
If the sprocket S is turning with an angular velocity ?S = 6 rad/s, and anangular acceleration of ?S = 2 rad/s^2. Find angular velocity and angular accelerationof link AB. Note that link AB shares an axis of rotation with sprocket S, but is free torotate separately from S (it’s not attached to the sprocket S). The pin at C is attachedto one of the chain links, and is moving vertically downward.
The system shown moves so that the acceleration of point B in the position shown is ag = -5i {m/s²}. Also, the angular velocity of bar BC is known to be 5 rad/s clockwise. Find the acceleration of the slider block C. (Note that the next question is related to this one.) y WAB WBC 1 m Taylor T e а. ac = -25.42i {m/s²} b. ac = 41.07i {m/s²} 1 m A 30° a. ac = -25.42i {m/s?} b. ac = 41.07i {m/s?} C. ac = -15.65i {m/s²} d. Te a ac = -45.73j {m/s?} е. ac = -33.87i {m/s²}
4. If the motor turns gear A with an angular acceleration of a = 2 rad/s when the angular velocity is wa = 25 rad/s, determine the angular acceleration and angular velocity of gear D. Note that Gear Band Gear C are attached, so rotate with the same w and a. B -100 mm C 50 mm D WA 40 mm 100 mm
Q6:- In the figure below a rod PR is constrained by guides to move horizontally and driven by a crank OA and a sliding block at P. For the given configuration determine the acceleration of PR when OA has an angular velocity of 10 rad/sec CCW and an angular acceleration of 50 rad/sec' cw. 5m 45
Bar OC rotates with a clockwise angular velocity woc = 5.3 rad/s and a counterclockwise angular acceleration doc = 4.6 rad/s². The bar OC is a slotted member which accommodates the pin A attached to the sector. Determine the angular velocity w and the angular acceleration a of the sector. The angular velocity and the angular acceleration are positive if counterclockwise, negative if clockwise. Assume OA = 500 mm, d = 385 mm, 0 = 21°. Answers: W = B a = i i d aoc rad/s rad/s² @oc
In the mechanism shown below, the wheel is pinned at the center. The radius from O to C is 0.2 m and link CB is 0.55 m long. CB makes an initial angle of 25° with the horizontal as shown. The hydraulic ram at B is moving left at 7 m/s. At the moment shown, what is the angular velocity of link BC and the wheel pivoted at 0? 0000 Ninbet tatis rad/s
b) Find the angular velocity and angular acceleration of disc B shown below, which is spinningatthe constant rate of ω2 = 90/πrpm. The disc is attached to collar A, which is rotating at the angular speed of ω1 = 5/π rpm, with the angular speed increasing at 0.5/π rpm/sec. Rod AB which connects the disc to the collar ispinned to the collar at A. The rod makes an angle of θ = 300 with the vertical, which is increasing at a constant rate of20/π0/sec.Express theAngularvelocityAcceleration of the disc in terms of a reference frame attached to thecollar.
The mechanism below has a crank that revolves clockwise at point O at a speed of 2000 rpm. Using vector diagrams, determine: a) The linear velocity of the piston and the angular velocity of the link AB about A. b) The angular acceleration of the link AB about A and the inertial resistance produced by the piston. c)Using trigonometry, confirm your results for the velocity in parts (i), explain your reasons behind which method is preferable, and identify the error margin for your velocity answers.
The relative acceleration of point A with respect to point B of the disk in Figure 1 is given as as/B = 3.347i + 1.283j. If the disk rolls without slipping, determine the angular velocity and angular acceleration of the disk at the instant. If, in other case, the disk rolls with slipping and the vM = 2 m/s to the left and vo = 2 m/s to the right, do you think that the process of determining its angular velocity and angular acceleration becomes easier or harder? A 45° B L--x M 0.2 m'0.2 m Figure 1
in the figure the wheel D rotates with an angular velocity ω1 of 2 rad/s counterclockwise. Find the angular velocity ωE of the toothed wheel E with respect to the ground at the instant shown in the diagram.Note: Solve bar AB and sprocket E by IC method and re-solve it again by the realtive method of velocities.