Methane is diffusing at steady state through a 0.5mm diameter and 4mm long tube containing nitrogen gas at 101.32 kPa and 298K. Methane entering the tube is at 2.31x10 Pa and leaving the tube at 1.013x10 Pa. The diffusivity of nitrogen in methane gas is 0.140 x10 m2/s. Calculate flux of methane. Mention the unit of the flux. Paragraph BIEE

Methane is diffusing at steady state through a 0.5mm diameter and 4mm long tube containing nitrogen gas at 101.32 kPa and 298K. Methane entering the tube is at 2.31x10 Pa and leaving the tube at 1.013x10 Pa. The diffusivity of nitrogen in methane gas is 0.140 x10 m2/s. Calculate flux of methane. Mention the unit of the flux. Paragraph BIEE

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

When the conservation of mass relations can be simplified
The diffusion coefficient of Ni in Cu at 1025 C is 10-9 cm2 s-1. How long does it take for the mean square root of the distance to be 1 cm?
Pre-lab 8: Cold Engine The experimental setup for this week's lab consists of a syringe connected to a metal can (reservoir), a cold bath (water - ice mixture) and a "hot" bath (water at room temperature). A schematics of the syringe - reservoir system is shown below. Plunger of mass m Filled with gas (air) Syringe of volume Vcor VH - Volume Vo includes tube + Metal can -Metal can submerged in water of temperature Тс or TH. Tube Stopper Figure 1: Schematic of the syringe - reservoir system. The syringe is essentially a glass cylinder fitted with a movable piston (plunger). The markings on the syringe indicate the volume of gas in the syringe, but do not include the additional, unknown volume, Vo, in the gas can and tubing.
URGENT sir
A thin plastic membrane is used to separate helium from a current.gaseous. Under steady-state conditions, a concentration of helium in the membrane is known to be 0.02 and 0.005 kmol/m³ on the inner and outer surfaces, respectively. If the membrane has a thickness of 1 mm and the coefficient ofbinary diffusion of helium to plastic is 10^(-9) m²/ s, what is the value of the flow diffusive?
A tanker ship is transporting 0.798 kg/m3 of a rare gas in its tank. After the fill-up, the 1.94 m long pipe used to fill the tank was left open for 10.4 hours. In that time, 11.7 x10-4 kg of the gas diffuses out of the tank, almost nothing compared to the original quantity of gas in the tank. If the concentration of that gas in our atmosphere is typically zero, and the diffusion constant of that gas is 2.13 x10-5 m2/s, what is the cross-sectional area of the pipe?
Use the Kedzierski (2003) refrigerant/lubricant mixture pool boiling model to predict the boiling heat transfer coefficient (hm) for a range of superheats (4T, = 8 K to 40 K) and Ts = 277.6 K: 5.9×107(1−x,)ph ATk, (1-e*) x, To Where 1₂ %₁ = = 9m T-T Г x Τσ PL-Pbx 5.9×107(1-x₂)ph AT 0.755lp₁ (1-x₁) _ 18.75Ãµ₁ (1—x₁) _ 18.75×10¯¹º[m]p, (1-x₂) Xp Prv XpPrv XpPrv Assume that λ = 1.34 for xb=0.005 and that λ = 0.3 for Xb = 0.02. The properties of the refrigerant (R123) at the film temperature are: KL (W/mK) 0.139 R123 Or (N/m) 179692.3 0.01764 hfg (J/kg) The properties of the mineral oil (lubricant) are: PL (kg/m³) 917.8 York-C VL (cSt) 60 Prv (kg/m³) 2.701 VL (m²/s) 6 × 10-5 OL (N/m) 0.026 1.) Plot hm vs ATs and le vs ATs for two lubricant mass fractions: x = 0.005 (use 2 = 1.34 for Xb = = 0.005) and x = 0.02 (use λ = 0.3 for xb = 0.02). Compare the predicted ro for the two mass fraction cases. Provide a plausible reason for why the boiling heat transfer coefficient for a given AT's for…
In a paint manufacturing process, two different colored paints are being mixed in an infinitelylarge drum.Paint A, with a concentration of 30% pigment, is pumped into the drum at a rate of 10 liters perminute.Paint B, with a concentration of 17% pigment, is pumped into the drum at a rate of 17 liters perminute.Both paints have the same density of 1.0 kg/liter.If the mixture is cotinuously stirred and drained from the drum at a rate of 22 liters perminute, what isthe concentration of pigment in the resulting mixture?
Which of the following is independent of flow velocity? a. Transverse diffusion b. Longitudinal diffusion c. Eddy diffusion d. Mass transfer
Gaseous hydrogen weakens the mechanical strength of cast iron. this phenomenon often occurs in cast iron pressure vessels containing 100% gas hydrogen. H2 gas dissolves in metallic iron and diffuses into solid non-porous iron by an interstitial diffusion mechanism. H2 gas does not need to penetrate far into the iron to have a negative effect on the mechanical strength of iron. In the present situation, 100% of H2 gas at 1.0 atm and 100°C is contained within a 1.0 m internal diameter and wall thickness of 2.0 cm. The solubility of hydrogen in iron in 100°C is 2.2x10-7 mol of H/g Fe atoms. The diffusion coefficient of atoms of hydrogen in solid iron is 124.0x10-9 cm2 /sec at 100°C. Initially, there are no H atoms in solid iron. How many hours will it take for the hydrogen level inside the iron metal reaches 1.76x10-7 mol H atoms/g Fe at a depth of 0.1 cm from the surface exposed to hydrogen gas?
The title of the experiment is the latent heat of evaporation Assume that (10%) of the mass of the shifted vapor is water at a .temperature (T = 100 ° C) It is not steam. What is the percentage of error obtained in the ?experiment
8