The strain rosette shown in figure was used to obtain strain data at a point on the surface of a machine part. If the readings from gages a, b, c were 650, -450,-585 (all in microns) respectively; which of the following is the shear strain on the surface?45°aLutfen birini seçina1370 micronb. 1570 micronc1400 micrond7600 micron

It is required to determine shear strain

Answered: The strain rosette shown in figure was…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

How do you dervive Hooke's law for the stress and strain components? This question pretains to the error in a measurement due to strain when using a long tape measure and that error is L-L0 . Where the error is introduced in inches into the measurement at a L length if the tape is pulled with P N (force) attached contains the question.
Calculate: 1. stress 2. strain 3. diameter of wire corrected to zero error
A tension test was performed on a specimen having an original diameter of 13.0 mm and a gauge length of 50 mm. Load (kN) Elongation (mm) 0 11.1 31.9 37.8 40.9 43.6 53.4 62.3 64.5 62.3 58.8 0 0.0175 0.0600 0.1020 0.1650 0.2490 1.0160 3.0480 6.3500 8.8900 11.9380 Using the data listed in the table, plot the stress-strain diagram. Use a scale of 20 mm = 50 MPa and 20 mm = 0.05 mm/mm. Part A From the diagram, determine approximately the modulus of toughness. Express your answer to three significant figures and include the appropriate units. U = Submit O μA Value Request Answer Units < Return to Assignment Provide Feedback ?
Can anyone help me with this question
Please show handwritten solution
2.5
Semiconductor strain gauges find their primary application in the construction of transducers, such as load cells and pressure transducers. Why do measuring instruments manufacturers usually use semiconductor strain gauges even though they are significantly more expensive than metallic strain gauges? Name two pros and two cons of these strain gauges compared to metallic strain gauges. Paragraph B A Lato (Recom... 19px... v T + v
When you buy a strain gauge, you have to pay attention to the GAUGE FACTOR, G. What is this gauge factor? Paragraph く BI U く A + v Lato (Recom... v 19px... v 5
A tension test was performed on a specimen having an original diameter of 13.7 mm and a gauge length of 50 mm. The data are listed in the table. Load (kN) Elongation (mm) 0 11.1 31.9 37.8 40.9 43.6 53.4 62.3 64.5 62.3 58.8 0 0.0175 0.0600 0.1020 0.1650 0.2490 1.0160 3.0480 6.3500 8.8900 11.9380 Plot the stress-strain diagram. Use a scale of 20 mm = 50 MPa and 20 mm = 0.05 mm/mm. Redraw the linear-elastic region, using the same stress scale but a strain scale of 20 mm = 0.001 mm/mm. From the diagram, determine approximately the modulus of elasticity. Express your answer to three significant figures and include the appropriate units. E = Submit Part B συ = Submit Part C ☐☐ μÅ of = Value Determine the ultimate stress. Express your answer to three significant figures and include the appropriate units. Request Answer μĂ Value Request Answer Units μĂ - Value Units Determine the fracture stress. Express your answer to three significant figures and include the appropriate units. ? Units ? ?
specimen of a metal 75 mm long was stretched with a force of 10 kN.The strain produced in the material was 10%. Find the crease in the length of the specimen. 7.5 mm 6.5 mm C) 8.5 mm 5.5 mm Question 5
The stress-strain diagram for a steel alloy having an original diameter of 0.3 in. and a gage length of 5 in. is shown in the figure below. (Figure 1) Figure σ (ksi) 80 70 60 50 40 30 20 10 0 0 0.04 0.08 0.12 0.16 0.20 0.24 0.28 0 0.0005 0.001 0.0015 0.002 0.0025 0.0030.0035 e (in./in.) < 1 of 1 ▼ Part A Determine the modulus of resilience. Express your answer to three significant figures. (ur)approx= Submit Part B (14)approx= Determine the modulus of toughness. Express your answer to three significant figures. Submit ■ AΣ¢ † vec Provide Feedback Request Answer |VL]ΑΣΦΠ = Ivec Request Answer [C] ? MIC ? in-lb in³ in-kip in³

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS