Match all the possible combinations between Column X (Cement compounds) and Column Y (Cement properties): Column - X (i) C3S (ii) C₂S (iii) C3 A Column - Y (P) Early age strength (Q) Later age strength (R) Flash setting (s) Highest heat of hydration (T) Lowest heat of hydration Which one of the following combinations is correct?

Match all the possible combinations between Column X (Cement compounds) and Column Y (Cement properties): Column - X (i) C3S (ii) C₂S (iii) C3 A Column - Y (P) Early age strength (Q) Later age strength (R) Flash setting (s) Highest heat of hydration (T) Lowest heat of hydration Which one of the following combinations is correct?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Choose the correct answer Flash-Set is the immediate stiffening of cement paste in a few minutes after mixing with water caused by. A-Low C3A content B-High C3A content C-Low C3S content D-High C3S content
Discuss the following properties of ordinary Portland cement and give their specification: a) Setting times, b) Soundness, c) Fineness and d) Strengths.
Concrete is described to be durable partially as it does not need any protective coating even in a harsh environment. of Select one: O True O False The consistency of the standard paste test is carried out to O A. Determine the W/C which will produce a normal consistency paste of O B. Determine the cement Fineness O C. Determine the cement setting time OD. Determine the cement soundness OE. All of the above
compute for the corrected amount of water needed in the concrete mix if the mass and fine coarse aggregates are 740 kg and 1100 kg, and both have a natural moisture content of 2% and 1.5% respectively. water/cement ratio is 0.5 and the mass of ratio of concrete is 1:2:3
choose one
-Before testing soundness of Portland cement, ------- should be tested in order to use its result in soundness test. compressive strength of mortar consistency of standard paste Tensile strengthof mortar fineness of cement all of them
We require a mix with a mean 28-day Required Average Compressive Strength of 35 MPa the size of the member and the spacing of the reinforcement require a slump of 50 mm and a maximum size of aggregate of 31 mm. Portland cement type I is used with specific gravity of 3.15, dry-rodded unit weight of coarse aggregate 1750 kg/m³ and bulk specific gravity (SSD) of 2.55. The fineness modulus of fine aggregate is 2.8 and bulk specific gravity (SSD) of 2.5 ,No air entrainment is required. Neglect water absorption and moisture content of both aggregates. The aggregates conform to the ASTM C33-84 requirements for grading. Estimate the quantity of (cement, fine aggregate, coarse aggregate and water) for 1m³ concrete.
Given the four concrete mixes as shown in the table below, one without water reducers and three (c1-c3) with water reducer. The most economic mix where the workability and compressive strength maintained as for the original mix (the mix without water reducers) is With water Reducer Without water Reducer C1 C2 C3 Cement, Kg/m3 850 765 850 850 Water, Kg/m3 465 419 370 465 Slump, mm 50 S1 50 S2 Compressive Strength (MPa) 38 fc1 fc2 fc3 Select one: O A. C3 О В. С2 О С.С1 O D. C1 and C2
What is the amount of cement in kilograms needed for the design mix? Use two decimal places
which is considered organic cement from the followings? * all of the mentioned Portland cement lime clay natural resins which is used to mitigate the sulphate problem in lime stabilisation * decrease the mellowing time increase water content all of the mentioned increase the compaction apply all lime required in one shot
Use ACI method .
Which of the options are correct for a 3m³ of concrete having design mix proportion of 1:2:7 (by volume) A Volume of cement required = 0.318 m³ B No. of cement bags required = 15 C D Volume of coarse aggregate = 2.5 m³ Volume of water required = 1m³