mass

Q: 11. Two cutting tools with tool life equations given below are being compared: Tool 1: VTº-1-150…

A:

Q: Compound axial member ABC has a uniform diameter of d-2.4 in. Segment (1) Is an aluminum [E,- 10,000…

A:

Q: Determine pressure in [kPa] in the cylindrical pressure vessel shown, if the measured hoop strain is…

A: Given, εhoop=500×10-6E=70 GPa=70×109 Paμ=0.33Ri=400 mm=400×10-3 mmt=6 mm=6×10-3 mm Internal diameter…

Q: is an example of Active Transducer.

A:

Q: - Rz (Ten-point surface roughness, The mean and valleys of distance b/us five Over a Wavines: ·Lay:…

A:

Q: 13.5 13.2 11. Apply a dia 0.5 at MMC straightness control to the axis of the part above and draw the…

A:

Q: 1) High speed spindles use special bearings designed to operate at high speed 2) Refrigerant flow…

A: All statements above are true. The special type of bearing are used for high-speed applications. In…

Q: la) If a 35 tonne block is raised to 110m and then falls to ground level (in generating mode) in 3…

A: 1a) Given         Mass, m = 35 ton = 31751 kg       Height, h = 110 m          Time, t = 3 min…

Q: Maybe someone can show the solution for this problem and be hand written pls.to be easy to…

A:

Q: ou can collec

A: A coring is designed with central open and the method is used for shown below.

Q: MA?

A: GIVEN: Explain RMA?

Q: 1. A wheel is used to turn a valve stem on a water valve. The wheel radius is 6 inches and the axle…

A:

Q: I’m a doing a stiffness compliance matrix. E_1 is 150 GPA; what are the units of E_1 when I do…

A:

Q: What type of scale is 10:1? O Full Scale O Enlargement Scale O Reduction Scale

A:

Q: Don't Use Chat GPT Will Upvote

A: Diagram-    Detailed Explanation of Reflection on a Curved Surface Understanding Key Concepts:1.…

Q: A composite beam is fabricated by bolting two 2.3-in.-wide by 14-in.-deep timber planks to the sides…

A:

Q: Define the elastic curve formulation y of the beam using Macaulay Function ) Define support…

A:

Q: I need help answering questions 1,2, and 3 pertaining to the print attatched below.

A: 1stIn the given drawing there are 4 surface texture symbols.

Q: The DP Transmitter device is used to measure level as an inferential measurement. When installing…

A: Differential pressure is calculated through the formula : Differential Pressure = Pressure High -…

Q: The state of an object varies over time, but at any particular points it is determined by:   Which…

A: The state of an object varies over time, then it must be dependent upon the state of the object…

Q: autonomous underwater vehicle) please give me assay about 1_Detalied Definition of The project…

A: A self-propelled, unmanned, untethered underwater vehicle, sometimes known as an AUV, is a…

Q: how do i find, Vba; Vbc; Vbd?

A:

Q: very valuable fx anand fy

A:

Q: E

A: Computer aided drawing is the way to draw the various views of the component. The orthogonal view,…

Q: mechanical design and drawing

A:

Q: Mention the primary features of RAC and why you should utilize it.

A: Given RAC To find Features Importance

Q: 1 Vav и dA TR² Ud 2 Tr dr R A .

A:

Q: * 14. An entomologist observes a 1-mm-long bug with a lens of focal length 5 cm. a) The bug is…

A: GivenSize of object=1mmFocal lengthf=5cm

Q: ead intrustions on example and help anwser it please and th

A: Jsolid Cylinder =πd432 DAC = 0.9 JAC =π 0.9432=0.064412467

Q: When you substitute AD in step 5, why do you get rid of the negative? In step 4 you keep it negative…

A:

Q: I need help solving problems 13, 14, and 15 pertaining to the print provided below.

A: 13.Dimensions of the same object should not be copied or we can say that the same information should…

Q: ood work on the promblem but the process is a bit hard to read, can you express

A: Given data as per question Tensile axial force, F=4500 N Outer diameter of tube, do=25 mm Inside…

Q: dH VdP = dS T т (1) show that equation (1) leads to equation (2). please don't use any other…

A: Given DatadH=Tds+VdPto ProvedHdPT=V1-βT

Q: The full sectional front view and top view of given object

A: AB is the Cutting plane

Q: 4. You want to transform the sample shown on the left into the structure shown on the right. How…

A: The photolithography process is nothing but the marking of the pattern on the substrate. It is the…

Q: A00007: Drafting Competencies - To create drawing view B' it is necessary to select drawing view 'A'…

A: Break view in the solidworks is used to display the larger drwaing in smaller drawing sheet by…

Q: R14 R6- R3- 14 R6 27 012 R14 014 R14

A: what do you want in this

Q: 2. Which of the following best describes how constant velocity is shown in a speed-time graph? a…

A: Correct option: (c) a straight horizontal line

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.