long pipe with 6cm outside diameter carries hot fluid and so, it is covered with 3cm thick insulation. it is proposed to reduce the conduction heat loss to the sorroundings by 3/4 of the present rate by further covering with same insulation. Calculate the additional thickness of insulation

long pipe with 6cm outside diameter carries hot fluid and so, it is covered with 3cm thick insulation. it is proposed to reduce the conduction heat loss to the sorroundings by 3/4 of the present rate by further covering with same insulation. Calculate the additional thickness of insulation

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Problem 5 High-strength stainless steel is required for use in building structures and equipment (e.g. , cranes). It is produced by heat treating quench-hardened steel in a process called tempering that reduces brittleness and imparts toughness. In a production facility, alloy steel plates (k=50 W/(m K), c=460 J/(kg K) and p=7865 kg/m³) of thickness 3 cm have to be tempered in a convective oven by heating them to 550°C. If the plates are initially at 40°C and the air inside the heat treating oven is at 700°C with a convective heat transfer coefficient of 45 W/(m? K), determine how long the plate has to remain in the oven.
Compare the different heat flux resulting from conduction through 1 in. of the follow·ing materials when subjected to a 30"F temperature difference: copper, steel, wood,glass fiber.
The heat loss from a fin is 6 W . The effectiveness and efficiency of the fin are 3 and 0.75 respectively . Find the heat loss from the fin, keeping the entire fin surface at base temperature?
Please fats. The answer in the box is incorrect
You are designing a 3m x 3m floor with radiant heating. The floor has 12 parallel pex pipes (k = 40 W/mK) of L = 3m, OD = 25mm and ID = 20mm. Hot water (TInfintiy 1 = 90oC, h = 200 W/m2K) runs through the pipes continuously. The surface below the pipes is perfectly insulated. Above the pipes, there is a 3mm layer of bonding material (? = 12 W/mK) and a 9mm layer of tile (k = 2 W/mK). Above the tile, there is air (TInfinity 2 = 25oC, h = 20 W/m2K). Properties of Air: k = 0.025 W/mK, Pr = 0.72, v = 1.847 x 10−5, u = 16.84 x 10−6, p = 1.2 kg/m3, B = 1/Tf (ideal gas), Hint: Assume that the “layer” of pipe starts at the center point (e.g. for conduction purposes, the pipe is OD divided by 2 thick). For convection, consider the entire pipe surface. a) What is the total heat rate entering the room above the floor? b) What is the temperature of the top of the tile?
A steam pipe 20cm in diameter is protected with a covering 6cm thick for which thecoefficient of thermal conductivity is k=0.003cal/cm deg. Sec in steady state .Find theheat lost per hour through a meter length of the pipe , if the surface of pipe is at 2000cand outer surface of the covering is at 300c
why the resistance of small machine is greater than the resistance of the large machine??
1. Calculate the overall heat-transfer coefficient (U=?) for a frame construction wall made of brick veneer (120-lbm/ft³) with 3-in. fiberglass insulation bats between the 2x4 wood studs (softwood) that are 16-in. on center. The wind velocity is 15-mph. Fill out the table below also utilizing materials data from the textbook. Also, calculate the total heat loss if the referenced wall was 9-ft tall and 35-ft in length set in Ohio, Clevland @ 99% winter OAT with an indoor setpoint of 75°F. Hint: 2x4 wood studs are 16-in. on center and 2-in. thick by 4-in. deep thus the empty space between each stud is 14-in. Remember use R = L/K & R = 1/C for materials. Between Frame (R-Value) At Framing (R-Value) Outside Surface 4-in. Face Brick (k=middle value) 1/2-in. Sheathing reg. density 3-in. Insulation Batt 2"x4" Wood Studs (k=middle value) 1/2-in. Gypsum Board Inside Surface Total (R-Value): ● U = ● Q= Btu/(hr-ft²-F) Btu/h Heat Loss
Water going into a pipe with a tempeture of T1 and going out T2 . ambient tempeture is T0. Develop an expression for T2 ( based on heat transfer) Length of the pipe Lh0 - convective heat transfer coefficient of the airhW -convective heat transfer coefficient of the waterk- pipe thermal conductivity (W/m·K)d – pipe diameter Use any other varilable that you need and can be found online easily .
Problem 6. ART TAT Consider the cylindrical pipe shown in the figure. Heat is being generated in the pipe wall at a rate of R in units of W/m³, and the thermal conductivity of the wall is k, the heat transfer coefficients at the inside and outside of the pipe are h; and ho, respectively. At a given location along the pipe axis, the temperature of the fluid flowing inside of the pipe is Ti and that at the outside is To i. ii. Find the expression for the temperature distribution in the pipe wall. Find the total heat transfer rate from the pipe to both fluids.
Problem 1 A hot water pipe is used for domestic applications is insulated with a layer of calcium silicate. If the insulation is 25 mm thick and its inner and outer surfaces are maintained at Ts,1 = 800 K and Ts,2 = 400 K, respectively. The outside diameter is 0.12 m. Given the thermal conductivity calcium silicate insulation equals to 0.09 W/m.K. A. Define the difference between lagged and unlagged pipes. B. Calculate the heat loss per unit length for this pipe.