AN PIPE LOCATED WHERE THE AMBIENT TEMPERATURE IS 32 DEG C, HAS AN INSIDE DIAMETER OF 50 mm WITH 10 mm INSULATION. THE OUTSIDE DIAMETER OF THE CORRUGATED ASBESTOS INSULATION IS 125 mm AND THE SURFACE COEFFICIENT OF STILL AIR (H, = 12; M2-K INSIDE THE PIPE IS STEAM HAVING A TEMPERATURE OF 150 DEG C WITH FILM COEFFICIENT H, = 6000 OF PIPE AND ASBESTOS INSULATION ARE 45 AND 0.12 THE THERMAL CONDUCTIVITY M2-K" DETERMINE THE HEAT LOSS PER UNIT M-K LENGTH OF THE PIPE.

AN PIPE LOCATED WHERE THE AMBIENT TEMPERATURE IS 32 DEG C, HAS AN INSIDE DIAMETER OF 50 mm WITH 10 mm INSULATION. THE OUTSIDE DIAMETER OF THE CORRUGATED ASBESTOS INSULATION IS 125 mm AND THE SURFACE COEFFICIENT OF STILL AIR (H, = 12; M2-K INSIDE THE PIPE IS STEAM HAVING A TEMPERATURE OF 150 DEG C WITH FILM COEFFICIENT H, = 6000 OF PIPE AND ASBESTOS INSULATION ARE 45 AND 0.12 THE THERMAL CONDUCTIVITY M2-K" DETERMINE THE HEAT LOSS PER UNIT M-K LENGTH OF THE PIPE.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Can someone please help me with creating an excel spreadsheet to calculate heat transfer phenomenon from a cylindrical fuel rod to the coolant? The excel sheet needs to be able to calculate these 3 things: Heat generated in a fuel rod at a distance ‘r’ from the center; Total Heat generated in the Reactor; the maximum temperature in the fuel and the cladding surface temperature, for a fuel rod at a distance ‘r’ from the center. The fuel used in this will be UO2 and there is a thin layer of helium that will separate the fuel from the cladding material. The user input parameters will be: the thermal neutron flux at the core, thermal conductivity of fuel, thermal conductivity of helium, thermal conductivity of the cladding, thickness of the helium layer, thickness of the cladding, diameter of the fuel pellet, fuel rod location (r), Cylindrical Reactor Size, and the fuel enrichment. For the fluid the user input will be coolant temperature and the heat transfer coefficient.
(Heat Transfer) A furnace wall is composed of 20.32cm of fireclay brick (k=1.32 W/m^2.k), 10.16cm mineral wool (k=0.039 W/m^2.k), and 10.16cm of common brick (k=0.69 W/m^2.k). The surface temperature of the common brick is 60°C and the interface temperature between the common brick and the mineral wool is 30°C. The temperature of the gases is 1000°C and the temperature of the outside air is 30°C. Determine the outside air coefficient hc=W/m^2.k
To maximize production and minimize pumping costs, crude oil is heated to reduce its viscosity during transportation from a production field. (1) Consider a pipe-in-pipe configuration consisting of concentric steel tubes with an intervening insulating material. The inner tube is used to transport warm crude oil through cold ocean water. The inner steel pipe (k, = 45 W/m-K) has an inside diameter of D₁, 1 = 150 mm and wall thickness t; = 20 mm while the outer steel pipe has an inside diameter of D₁,2 = 250 mm and wall thickness to = 1;. Determine the maximum allowable crude oil temperature to ensure the polyurethane foam insulation (k = 0.055 W/m-K) between the two pipes does not exceed its maximum service temperature of 7p,max = 70°C. The ocean water is at T, = -5°C and provides an external convection heat transfer coefficient of h, = 500 W/m²K. The convection coefficient associated with the flowing crude oil is h; = 450 W/m².K. (2) It is proposed to enhance the performance of the…
A furnace wall consists of 2 ft of brick . The brick has athermal conductivity of 0.6 Btu/ hr sq ft ( ° F /ft), a specific heat of0.2 Btu/ lb ° F, and a density of 110 lb/cu ft. The temperature atthe inside surface of the wall is 1100 ° F , and at the outside surface,200 ° F .(a) Calculate the thermal diffusivity of the brick .(b) Calculate the heat loss per hour through a wall 10 ft high and10 ft long(c ) Calculate
As shown in the sketh below, a steam pipe of 0.12-m inside diameter is insulated with a layer of calcium silicate. "2. Ta2} 1. Ta,1} Steam Insulation (a) If the insulation is 10 mm thick and its inner and outer surfaces are maintained at T, = 800 K and Ta = 490 K. respectively,. what is the rate of heat loss per unit length (q) of the pipe, in W/m? (b) Determine the rate of heat loss per unit length (d), in W/m, and outer surface temperature T,2, in K, for the steam pipe with the Inner surface temperature fixed at T = 800 K, inner radius = 0.06 m, and outer radius n = 0.18 m. The outer surface is exposed to an airflow (T 25°C) that maintains a convection coefficient of h = 25 W/m2-K and to large surroundings for which Tur = T, = 25°C. The surface emissivity of calcium silicate is approximately 0.8.
1- Microwave radiation is incident on one side of a planar wall with a heat conductivity coefficient k. (x=0) -D°b=(x)b leads to volumetric heating. While this surface is 9(W/m²) microwave radiation is fixed. kept at a constant temperature To, the other surface at x=L is very well insulated. Determine the temperature distribution T(x) in terms of x, L, k, qo and To.
A plane wall of an oven with an insulation coating is attached to an insulated wall. The thermal conductivity and thickness of the insulation coating are 0.1 W/(m K) and 1 mm, respectively. The material of the plane wall is stainless steel 304. The density, thermal conductivity, and specific heat capacity of the stainless steel 304 are 7900 kg/m³, 74.9 W/(mK), and 477 J/(kg-K), respectively. The wall thickness of the stainless steel 304 is 15 mm. The temperature of the plane wall with the insulated coating is initially maintained at 30 °C. Suddenly, hot gas with a temperature of 1000 °C enters the oven. The convection heat transfer coefficient at the insulation coating surface is 70 W/(m²-K). Insulation Coating Stainless Steel 304 Oven Gas Perfectly Insulated Wall 1 X L 3-1) What is the overall heat transfer coefficient per unit area from the gas to the surface of the stainless steel? The answer should be given in the unit of W/(m²-K). 3-2) What is the value of the Biot number? 3-3)…
If a heat transfer coefficient of 2.84 W l(m2 • K) exists on each of the two inside faces of two sheets of 6.35-mm-thick glass separated by an air gap, calculate the gap that can be used such that the rate of heat transfer by conduction through the air gap equals the rate of heat transfer by convection. What is the rate of heat transfer if this gap is exceeded. The thermal conductivity of air of 0.0242 WI (m . K). Solve for temperature of 20°C and 12°C on the outside surfaces of the glass. Would the calculated gap change in value for different values of the surface temperatures? Would there be any advantage to increasing the gap beyond this calculated value?
A hot water pipe is used for domestic applications is insulated with a layer of calcium silicate. If the insulation is 25 mm thick and its inner and outer surfaces are maintained at Ts,1 = 800 K and Ts,2 = 400 K, respectively. The outside diameter is 0.12 m. Calculate the heat loss per unit length of the pipe. Given the thermal conductivity of calcium silicate insulation equals to 0.09 W/m.K.