At a particular section of a beam with the given cross-section,an internal shear force V and bending moment M act.Determine the following:Заa. Location of the neutral axis relative to the topmostfiber (in)b. Moment of inertia with respect to the neutral axis (in“)c. Maximum flexural stress in the cross-section (ksi)d. Maximum shear stress in the cross-section (ksi)e. Net force acting on the hatched area (kips) – indicatewhether tensile or compressivebV = 100 kipsM = 500 kip-ina = 1.6 inb = 2.73 in

Answered: Image /qna-images/answer/72aa976c-b9b6-4c0d-a0d8-dc143ab1ed5d.jpg

Location of the neutral axis relative to the topmost fiber (in) Moment of inertia with respect to the neutral axis (in) Maximum flexural stress in the cross-section (ksi) Maximum shear stress in the cross-section (ksi)

Location of the neutral axis relative to the topmost fiber (in) Moment of inertia with respect to the neutral axis (in) Maximum flexural stress in the cross-section (ksi) Maximum shear stress in the cross-section (ksi)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Prob. 2.9-10. At room temperature (70°F) and with no axial load (P = 0) the extensional strain of the prismatic bar (Fig. P2.9-10) in the axial direction is zero, that is, € = 0. Subsequently, the bar is heated to 120°F and a tensile load P is applied. The material properties for the bar are: E = 10 × 10³ ksi and a = 13 x 10-6/F, and the cross-sectional area of the bar is 1.8 in². For the latter load-temperature condi- tion, the extensional strain is found to be €x = 900 × 10 6. (a) Determine the value of the axial tensile load P. (b) De- termine the normal stress and the shear stress on the oblique plane NN'. (Note: The total strain is the sum of strain asso- ciated with normal stress o (Eq. 2.14) and the strain due to change of temperature AT (Eq. 2.8).) in. P Gage measures extensional strain Ex N N' 25° P2.9-10 X
In a laboratory test of a beam loaded by end couples, the fiber at layer -3 AB as shown are found to increase 40 x 10mm while those at CD decrease 70 x 10 mm in the 250-mm-gage length. Using E= 150 GPa, determine the flexural stress at the top fiber. Answer must be in MPa. -3 Given: a 60 mm, b 120 mm, and C 80 mm. gage length a mm A 8. b mm D. c mm
Two polymer bars are connected to a rigid plate at B, as shown. Bar (1) has a cross-sectional area of 1.58 in. and an elastic modulus of 2430 ksi. Bar (2) has a cross-sectional area of 0.714 in and an elastic modulus of 4110 ksi. Assume Ly-18 in., Lz-47in, Q=6,4 kips, P-3.2 kips, and R-128 kips. Determine the horizontal deflection of end Crelative to end A. (1) Answer: uCA in.
A 5.2-m-long aluminum tube (1) is to be connected to a 2.2-m-long bronze pipe (2) at B. When put in place, however, a gap of 9 mm exists between the two members, as shown. Aluminum tube (1) has an elastic modulus of 69 GPa and a cross-sectional area of 1980 mm2. Bronze pipe (2) has an elastic modulus of 93 GPa and a cross-sectional area of 3970 mm2. If bolts are inserted in the flanges and tightened so that the gap at B is closed, determine: (a) the normal stresses ?1, ?2 produced in each of the members. (b) the displacement (change in length of material (2), up is positive) uB of flange B with respect to support A. 5.2 m 2.2 m Answers: (a) 0₁ = (b) Ug = C (1) B (2) -95.40 1.126 9 mm MPa, 0₂ = mm. -47.58 MPa
to the direction of loading. When When solving for Normal/Axial/Compressive/Tensile Stress we look at an area of our member that is solving for basic Shear Stress we look at an area to the direction of loading. This is because of how the members will fail in either situation and what resists that failure. Parallel, Parallel 1000 Parallel, Perpendicular Perpendicular, Parallel Perpendicular, Perpendicular
11. Iwo beams, one having square cross section and another circular cross-section, are subjected to the same amount of bending moment. If the cross-sectional area as well as the material of both the beams are same then (A) Maximum bending stress developed in both the beams is the same (B) The circular beam experiences more bending stress than the square one (C) The square beam experiences more bending stress than the circular one (D) As the material is same both the beams will experience same deformation
Compound axial member ABC has a uniform diameter of d = 1.25 in. • Segment (1) is an aluminum [E1 = 10000 ksi] alloy. The length of segment (1) is L1 = 100 in. • Segment (2) is a copper [E2 = 17000 ksi] alloy. The length of segment (2) is L2 = 140 in. When axial force Pis applied, a strain gage attached to copper segment (2) measures a normal strain of ɛ2 = 2300 uin./in. in the longitudinal direction. What is the total elongation of member ABC? L2 (1) Aluminum B (2) Copper Answer: in, AL = i
The composite beam is made of steel (A) bonded to brass (B) and has the cross section shown. It is subjected to a moment of M = 6.3 kN?m .Ebr = 100 GPa, Est = 200 GPa A: Determine the maximum bending stress in the brass. B:Determine the maximum bending stress in the steel. C: Determine the stress in the brass at the seam where the brass and steel are bonded together. D:Determine the stress in the steel at the seam where the brass and steel are bonded together. B M 175 mm 150 mm 200 mm
Internal tensile forces in a rod subjected to a uniaxial pulling load
TWO SOLID CYLINDRICAL RODS ARE JOINED AT B AND LOADED AS SHOWN. ROD AB IS MADE OF STEEL (E = 210 GPa) AND ROD BC OF BRASS (E = 108 GPa). DETERMINE (A) THE TOTAL DEFORMATION OF THE COMPOSITE ROD ABC, (B) THE DEFLECTION OF POINT B. 40 KN 400 mm 600 mm A B C 30 mm 50 KN 50 mm
I will rate immediately
A stress developed if the applied force is parallel to the resisting area refers to: O tangential O bearing O normal. O simple