load current is to vary from 12 to 100 mA. Find the value of series resistance R to maintain a voltage of 7.2 V across the load. The input voltage is constant at 12V and the minimum zener current is 10 mA. Q2. A 7.2 V zener is used in the circuit shown in Figure below and the R Iz Eo RL Vz E, = 12 V

load current is to vary from 12 to 100 mA. Find the value of series resistance R to maintain a voltage of 7.2 V across the load. The input voltage is constant at 12V and the minimum zener current is 10 mA. Q2. A 7.2 V zener is used in the circuit shown in Figure below and the R Iz Eo RL Vz E, = 12 V

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

IN ALL CALCULATIONS AND THE USE OF THE FOUND VALUES IN THE EQUATIONS, THE PROCESS WILL BE MADE WITH 3 DIGGERS AFTER THE COMMA. Thank you
half bridge given in the figure for the rectifier circuit; Output current and voltage waveform draw
In the circuit shown below, if VA= 1V and V-2V, the statuses of the diodes are (Assuming ideal diodes) D₁ VA V₂₁ D₂ ERL Vout Select one: O a D₂ is ON, D₂ is ON O b. None of these Oc. Dy is OFF, D₂ is ON O d. Dy is ON, D₂ is OFF
If the load resistance value Rl is 2 kohm in this circuit and the DC component of the output signal is 5V, calculate the AC output power of this circuit. The diodes used are silicon diodes, their operating voltage is 0.7 Volt and their resistance can be neglected since they are very small.
A 500 ohm resistor is connected to a 12V source at one terminal and a 10V zener diode of 250 mW and a 5K ohm resistor are connected to the other terminal. What is the maximum current of the zener diode?
32 Basic Zener Regulation Past If the input voltage, Vi = 40 V, the zener diode voltage Vz = 15 V, R = 1002, load resistance is 802, and Pzm = 1 W. The following statements are true except, * load voltage is exactly the same as Vz load voltage is greater than Vz Power delivered by the input voltage is 10 Watts power dissipation of R = 6.25 Watts IN+ R₂
-8V R=1.2k2 R2= 2-5kS2 Silicon diode Construct the circuit in more easy wawy and kindly solve the following thank you withexplanation pleare Diode condition * current * Diode Current Diode voltage (Vo) Output voltage ( V5)
You are an electrician working on an overhead crane. The crane uses a large electromagnet to pick up large metal pipes. The magnet must have a minimum of 200 VDC to operate properly. The crane has an AC source of 240 V. You are given four diodes that have a peak voltage rating of 400 V each. These diodes are to be used to form a bridge rectifier to convert the AC voltage into DC voltage. Is the voltage rating of the diodes sufficient? To the nearest volt, what will be the DC output voltage of the bridge rectifier?
Draw the circuit generation of direct current Doubler circuit by put another stage (3 Stages)
A bridge rectifier shown below will have a positive pulsating voltage as its output, To convert the output to be negative, D . O a. D1 must be reversed b. D1, D2, D3 and D4 must be reversed O c. D1, D2 and D# must be reversed O d. D1 and D@ must be reversed O e. none of these
You are told that the approximate diode knee voltage is 750mV, but you need to know for sure. You are told that the diode's saturation current is I, = 2.27fA. (2.27x10-15 A) and V=25mV. Determine VD. Iterate until you have the answer to 2 significant figures.