ll standpipe as shown in Figure Q1(a) with an open top has an inner diameter d = 21 m and wall thickness t = 25 mm, where  1.Given the weight density of water γ = 9.81 kN/m3 and water pressure is p = γ h,calculate the height h of water that will produce a circumferential stress of 12 MPa in the wall of the standpipe 2.Calculate the axial stress in the wall of the tank due to the water pressure.

Q: A cylinder filled with oil is under pressurefrom a piston, as shown in the figure. The diameter dof…

A: Given   Shear stress = 5500 psi          Load, F = 3500 lb   Diameter, d = 1.80 in Find   Thickness,…

Q: 100 m 40 m 250 m conductor with a specific gravity of 40.10-3 kg/m.mm2 was drawn between two poles,…

A:

Q: The pressure vessel shown.above is made from 4 mm thick steel plate. A pressure of 3.5 MN/m² is…

A:

Q: A cylindrical tank containing thickness Q2) compressed air has wall t 12mm and inside radius r=…

A: The stress that tends to burst a cylindrical pressure vessel circumferentially is termed…

Q: Ex Yxy Yyx 3.3.2 Drawing the Mohr's Circle Example: - Ex = 70με &y = 40με Yxy = 60 με لاوه لان Yyx…

A: Given data:- εx=70 με (Tension) εy=40 με (Tension) γxy=60 με (Positive) To draw:-Mohr's Circle

Q: Example 5 The plane gate (Fig. 2.30) weighs 2000 N/m length normal to the plane of the figure, with…

A:

Q: che effects of temperature and she

A: given:

Q: A cap plate at the bottom of the brace distributes the load P = 660 kN to four flange plates…

A:

Q: (a) Draw a freebody diagram. (b) Find Fy and Fx. a) 0 A=0.01 m² P=220 kPa atm こ V2=16 mis H2= 0.0025…

A: The area at point 1 is The pressure at 1 is The velocity at 2 is The area at point 2 is The density…

Q: (b) A cylindrical tank of outer diameter 3.0 m and wall thickness 20 mm is open at the top as shown…

A: givend=3m=3000mmt=20mmγ=9.81 kN/m3σc=8MPa

Q: A steel pipe of length L= 5 ft, outside diameter d₂= 9.3 in., and inside diameter d₁= 4.7 in. is…

A:

Q: Find the width of a heavy-single ply leather belt (8.75 hp/in) transmitting 11 hp at 1800 rpm motor…

A: Given, Heavy - Single ply leather belt Power, p = 11hp; Speed of the motor, N = 1800 RPM cm =0.696…

Q: A cylindrical tank with hemisphericalheads is constructed of steel sections that are…

A: A cylindrical vessel or shell may be thin or thick depending upon the thickness of the plate in…

Q: The spar shown in the figure is wood (s.g.=0.62), 2 in by 2 in by 10 ft, and floats in sea water…

A: Buoyant force must balance the weight of wood and weight of steel for given configuration.

Q: A steel pipe of length L= 5 ft, outside diameter d₂= 9.3 in., and inside diameter d₁= 5.1 in. is…

A: Given:Length of the pipe, L=5 ftOutside diameter, d2=9.3 inInside diameter, d1=5.1 inAxial force,…

Q: Part (a) Calculate (i) The longitudinal stress in the wall of the pressured vessel, L (ii) The hoop…

A:

Q: Calculate the tangential stress at a point on the plate that forms a cylindrical reservoir, known as…

A:

Q: The composite shaft, consisting of aluminum, copper, and steel sections, is subjected to the loading…

A:

Q: (iii) The longitudinal strain, ez (iv) The hoop strain, eĦ Enter your answers to eT and e# in the…

A: Hoop and circumference stresses are calculated. Strain values are calculated involving poisson ratio…

Q: In figure, if the floating ball radius is blä 5 0.5 m and its density= 2000 N/m3, the * ? cable…

A:

Q: OUsi ng spheric al pressure Vessel is it safe based on maximum internal pressure all ow able mi ni…

A: 1) a] Maximum internal pressure allowable : p = σ * 4 * t / d p = σ * 4 * t / d p = 103421 * 4 *…

Q: A circular shock absorber, as shown in the figure below, is designed to support a set of sensitive…

A: Force applied (F): 1000 NDiameter of aluminum circular bar (d1): 4 mmDiameter of hollow circular…

Q: A block R of rubber is confined betweenplane parallel walls of a steel block S (see figure).…

A: Strain in x direction,εx=σxE-νE(σy+σz)Here,σx,σy,and σz is the stress in x , y and z…

Q: A rail line is laid so that there is no stress in rails at 15°C. The rails are 500000 mm long. α =…

A:

Q: How much fluid is required to raise the pressure in a thin cylinder of length 3 m, internal diameter…

A: This question is related to the thin cylinder problems. In the case of a thin cylinder, there are…

Q: ckness of th SS yield stress SS = T A ga:

A:

Q: A conductor with a specific gravity of 40.10-3 kg/m.mm2 was drawn between two poles, which are given…

A:

Q: QUESTI ON 2 X 2.1 A spherical pressure vessel has a mean diameter of 400 mm, and a wall thickness of…

A:

Q: Part A |Fucl = 0.97 D HÅ 5m 2 m Determine the magnitude of the projected component of the F= 5 kN…

A: Determine the magnitude of the projected component of the F= 5 kN force acting along the axis BC of…

Q: A steam pipeline measures 20 m at a temperature of 20 °C. The pipeline carries superheated steam at…

A: Given, L = 20 m t1 = 20o C t2 = 300o C E = 210 kN/mm2 α=11.2×10-6 C

Q: Q.2 A thin cylindrical shell, 1.5 m internal diameter, 2.4 m long, internal volume 4-23 m³, plates…

A:

Q: Find ly and Iz for the section below assuming D=300mm,B=200mm, and t=22mm.

A:

Q: I need the answer as soon as possible

A: Given data: Weight is 500 N is supported on two metallic ropes which is; 900  and 1200 Using lamis…

Q: A spherical tank of diameter 1.275 m and wall thickness 40 mm, contains compressed air at a pressure…

A: The diameter of the spherical tank is given as, d=1.275 m. The thickness of the spherical tank wall…

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.