Let the message (modulating) signal be m(t)= sinc²(1) and the carrier Signal be c(t) =10cos(1000.zt). a Determine the double sideband (DSB) amplitude modulated signal with modulation index 0.8 in time domain and sketch the modulated signal in frequency domain. b. Determine the double sideband suppressed carrier (DSB-SC) amplitude modulated signal in time domain and sketch the modulated signal in frequency domain. c. Find the Fourier transform of m(t), where m(t) denotes the Hilbert transform of m(1). d. Determine the lower single sideband (LSSB) amplitude modulated signal in time domain and sketch the modulated signal in frequency domain. e. Determine the phase modulated (PM) signal with deviation constant k =5 rad/V in time domain. Find the effective bandwidth of the modulated signal. %3D

Let the message (modulating) signal be m(t)= sinc²(1) and the carrier Signal be c(t) =10cos(1000.zt). a Determine the double sideband (DSB) amplitude modulated signal with modulation index 0.8 in time domain and sketch the modulated signal in frequency domain. b. Determine the double sideband suppressed carrier (DSB-SC) amplitude modulated signal in time domain and sketch the modulated signal in frequency domain. c. Find the Fourier transform of m(t), where m(t) denotes the Hilbert transform of m(1). d. Determine the lower single sideband (LSSB) amplitude modulated signal in time domain and sketch the modulated signal in frequency domain. e. Determine the phase modulated (PM) signal with deviation constant k =5 rad/V in time domain. Find the effective bandwidth of the modulated signal. %3D

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q. Choose the correct answer (.. 1. increases as the length of channel increases. (interference, distortion, additive noise, attenuation). 2. 100% modulation is produced in AM when carrier frequency exceeds signal frequency, amplitude equals signal amplitude, amplitude exceeds signal amplitude). 3. A 10 MHz carrier of peak value of 10 V is amplitude modulated by a 10 kHz signal of amplitude 5 V. The amplitude of each sideband frequency is 4. A Phase-Locked Loop (PLL) is a feedback circuit consisting of VCO, all of the above). 5. The line connecting the positive and negative peaks of the carrier waveform is called (Peak line, Maximum amplitude, Modulation index, Envelope) 6. Thermal noise power is proportional to (T², 1/T, T, T'2) 7. Which of the following is an advantage of SSB over DSB? (No change in spectrum space, Reduce in spectrum space, Carrier is suppressed, Power is not wasted on the carrier). 8. Which one of the following is not true with respect to SSB signal? (Hard to…
In FM modulation, the magnitude and direction of the frequency shift  is proportional to the amplitude and polarity of the modulating signal.Thus, the general expression of any base-band signal frequency modulated onto a carrier
i need the answer quickly
D E F
2
1. The CT signal x(1)-6cos (800zt) + 8cos² (mæt) is eritically sampled (Nyquist rate) by f-8000 Hz. Find: i. The value of m. ii. The frequency components of the signal. The frequency resolution (A) of the output spectrum if the sampled signal is processed by 32point-DFT. iii. iv. Define frequency resolution.
B. FM modulated signal is transmitted over a noisy transmitter modulator, with the power spectral density of noise being as shown in Figure 1 (W is the information frequency with 1 KHz, Sn (f) is the power spectral density for the noise). The FM equation and transmitter is shown in figure 2. 1. Derive the FM modulated signal for narrowband modulation 2. Determine the power of the narrowband FM modulation 3. Determine the signal to noise ratio for the narrowband FM modulation s4) - A, co 2f1 + 2n, mr dr 2 mk, Baseband signal Narrowband Integrator phase modulator Frequency maltiplier FM signal N4. Crystal- contralled oscillator Figure 1 Figure 2
I need the answer as soon as possible
Q6. Figure Q6 shows the line spectrum of a modulated signal (all components are positive and real). 3 1 232 234 236 238 frequency/kHz Figure Q6: Line spectrum of a modulated signal (a) Describe the modulation scheme. (b) What are the values of the carrier frequency, modulation frequency and the modulation index? (c) What is the transmission efficiency (ratio of modulated to total power) in this example? (d) The reception of this signal is undertaken with a superheterodyne detector using an intermediate frequency of 110 kHz. What is the appropriate local oscillator frequency? (e) Demodulation of this type of signal is usually accomplished using an envelope detector. Describe the principles of operation of an envelope detector and sketch an example circuit. (f) What considerations should be made about the component values in the design of an envelope detector in order to demodulate the signal after shifting to the intermediate frequency? Relative unitsS
If the amplitude of the modulation signal voltage was given to be -4v and +4v and carrier amplitude also given to be -22v and +22v, by suitable waveform diagram determine the Am modulated output. Remember to provide all necessary wave forms in practical terms.
What is the objectives of generate discrete signal by using sampling frequency?