Length of Wall 1 = Length of Wall 2 = Length of Wall 3 = m Wall 2 30 cm 3 m 3 m D.P.C 1:2:4 Ground Level m 6 Wall 3 Step - 2 40 cm 60 cm 2 m Step - 1 50 cm 20 cm PCC Wall Wall 2 80 cm 30 cm 3 m EEE 632

Length of Wall 1 = Length of Wall 2 = Length of Wall 3 = m Wall 2 30 cm 3 m 3 m D.P.C 1:2:4 Ground Level m 6 Wall 3 Step - 2 40 cm 60 cm 2 m Step - 1 50 cm 20 cm PCC Wall Wall 2 80 cm 30 cm 3 m EEE 632

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A drain pipe is to be laid between two points. One point is 13'0" higher in elevation than the other…

Q: 2/ For the plan (hexagon shape) and section of the wall shown in No. 1. Calculate quantities for…

Q: Explain any three types of excavation

A: Excavation is the process of excavating and removing volumes of earth or other materials for the…

Q: Define the various types of boring with neat sketches ?

A: Brief concept- Boring- It is generally used for depths greater than 3 m or when difficult…

Q: Define two-way flat slab.

A: Slabs are 2D construction members that are used to provide cover for floors and tranfer the load…

Q: Problem I. A steel beam cross section is assembled as shown by bolting the channel, C200 x 27.9,…

Q: add the data for crown slope, tangent runout, and lane width: V = 80KM/H , lane width = 4m R =…

A: Question is based on the pavement design . Speed of vehicle, lane width , radius of curvature and…

Q: 5. According to Fig. (a), (b), (c), specify what principle or relevant requirement is used on…

A: Dynamic tolerance diagram: Dynamic tolerance diagram 2 equal planes portray the volume of room used…

Q: What is deep excavations?

A: Excavation is the process of removal of soil or rock from ground surface for various purposes such…

Q: Engineering Surveys (Earthworks) A rectangular prism has the following offsets at every corner:…

Q: Define fixed-earth-support method.

A: The fixed earth support method is a basic method by which anchored sheet walls are designed. In this…

Q: Explain the outflow and inland river and the side reserve by drawing it by hand. Kindly provide…

A: Lakes are naturally occurring land depressions that are full of water.

Q: Given the end area of cut and fill of soil as in Table Q4(c). If the material bulks after excavation…

A: Data Given: Bulks after excavation = 10% Shrink = 12% Chainage distance = 100m Asked: Draw Mass…

Q: QUESTION TwO (a) Determine the side widths and areas of the following cross sections:- Fill section…

A: Given : Fill section consisting sides with slopes 1 in 3 and 1 in 3 Bottom side 1 in 10 Central…

Q: 1/ For the plan and section of the wall shown below. Calculate quantities for each of the following…

Q: Find hydraulic radius 5 ft ㅗ - 10 ft -

A: Given data : The value of width of rectangular section b=10 ft The value of depth of water d=5 ft…

Q: Describe Typical earth dam sections.

A: Earthen Dam:

Q: 1. What is the stationing of the end of excavation? 2. Find the volume of fill by end area method.…

Q: 1. The following is a set of notes of the earthworks of a road embankment Sta 1+020 9.0 4.5 +2.0 4.5…

Q: Q3) The figure below represent the horizontal coordinates (x, y) and vertical coordinate -ground…

A: Surveying a branch of the construction industry where balancing between different points on the…

Q: Two irregular sections of 60 m apart have an area of 32m2 and 68 m2 respectively with a base width…

Q: ITEM NO. 4 The cross section notes below are for ground excavation for an 8 m wide roadway. STA…

Q: Why Crossdrainageworks areconstructed? Enlist different types of Cross drainage works. And describe…

A: The cross drainage works are constructed, when a stream and canal intercepts. These structures are…

Q: An 8m steel tape was purchased and advertised as follows: Standard temperature : 24°C Standard Pull…

Q: draw depth of stair landing = 1200 mm floor to stair landing height = 1500mm

A: Given depth of stair landing = 1200 mm floor to stair landing height = 1500mm To draw a staircase…

Q: Define Reinforced Earth.

A: The reinforced earth is defined as “the composite material formed by the soil with low bearing…

Q: b. Volume of the Work Area Building Perimeter ii Centerline of Work Area: i Volume of Work Area…

A: To find the total volume of excavation.

Q: The cross section at station 2+60 has a cut area of 9 ft² and a fill area of 4 ft² and the cross…

A: Given that, Cut Area of cross-section at station 2+60, A2+60=9ft² Cut Area of cross-section at…

Q: How many blocks are necessary to build a 261 (S.F.) wall area with the following conditions? Note Do…

Q: Discuss the advantages and disadvantages of calculating volumes of cut and fill by using the “grid…

A: The most suitable method of calculating volumes of cut and fill volumes is by using a digitizer and…

Q: Describe hydraulic fill in detail.

A: Hydraulic fill is material that is dredged from from a borrow area or borrow pit and placed at a…

Q: What perameters are used for Existing ground level ?

A: Solution: Ground level means the existing level of the site at any of the point. When earth filling…

Q: What is the purpose of wave equation analyses?

A: Pile foundation is a type of deep foundation in which the load is carried by skin friction as well…

Q: Y5 Y4 Y3 1 0.95 1 1 1 0.8 1 1 1 0.3 0.8 0.8 1 1 top 0.5 0.7 bottom 10 mm scale 1:500 1- 1, 1, 1,

A: It is given: Scale of plan = 1; 500 There are two methods that are asked in the question Counting…

Q: Define COMPRESSIBILITY AND SETTLEMENT

A: Compressibility- It is defined as the change in volume of soil due to the application of mechanical…

Q: 4' Deep 32' 5' 2" Deep A 21' Volume of Trench Excavation 4' 8" Deep Plan View of Building Section…

Q: Write down the purpose of boring?

A: Boring Boring is the process of drilling of holes in the ground. That can either on the ground or on…

Q: What are some concerns about clear cutting?

A: "Clearcutting" is defined as "the falling and clearance of all plants from a specific forest…

Q: What would the cut length be for a section of conduit measuring 12 inches up, 18 inches right, 12…

A: Cut length of a conduit or pipe refers to the true length of the pipe without the bends.

Q: Describe boring spacing and depth?

A: The boring is done for the following purposes- Soil Investigation Determining the depth at which…

Q: Draw to show the subgrade working area.

A: Subgrade soil - The integral part of the road pavement which provides adequate support to the…

Q: Station A (10+040) 9.50 11 +3.00 +2.00 +4.00 Station B (10+060) 6.50 8.00 +1.00 1.20 +2.00

Q: Show complete solution on Length for laying out, and Width for laying out.

Q: Write down the main groups of levelling types and explain all of them in detail

A: leveling is the branch of the surveying which used to measure vertical distance with respect to the…

Concept explainers

Measuring site work, Excavation and Piling

Bid drawings typically include very little material about the precise requirements of site work operations, measuring site work and excavation work differs from measuring most other works on a construction project. The actual site work conditions are not provided and also the dimensions of the excavations are not known during the pre-construction phase. The precise measurement of the excavation and backfill of the earth material and topsoil is important for a contractor to decide upon the total cost required for the process. All the works should be carried out under OSHA (Occupational Safety and Health Administration) standards to ensure the safety of the workers.

Question

Excavation of Earth Work below Ground Level: Volume (m3
)

0.30
WALL
3m
or
S/S
D.P.C
STEP-II
0.60
0.40
0.20
STEP-I
o. po
p.C.C
0 80
0.50

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 cross section area of excavation

VIEW

Step 2 lnghth

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Measuring sitework, excavation and piling

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Compute the volume of excavation between station 24+00, with an end area of 711 ft2, and station 25+00 with an end area of 515 ft². Answer will be in yards cubed, round to the nearest whole cubic yard. 2270 2720 61290 20430 000
Define Blanket Drains.
2. Several lines of levels were run over different routes from BM1 in order to set BM2 and establish its elevation. The lengths of these routes and the value of the elevations determined are shown blow. Determine the most probable elevation of BM2. Show your final answer and your computations in the table. Any additional work may be shown below the table. Route a b C d Length (miles) 4 8 2 6 Measured Elevation (ft) 973.09 973.56 973.24 973.70
A mining company is going to drive a new entry which will extend off of a point A (N 9425, E 4250) position C current entry. Known location points in the current entry are and B (N 10216, E 6312). The new entry will be driven from point A to a new (N 3392, E 8438). Include a sketch with points labeled. Determine the following: a. The distance of the new entry to point C. b. Вearingac BearingCA с.
Nice, thanks. But where that 10 kN/m2 come
Describe about the Horizontal Drainage.
Draw the following lot bearings on 1:100 scale
Determine the interior angles of the parcel shown below. Provide a check. Show answers on the space provided.
Define Sand Drains.
Asap plxxxxx
Determine the interior angles of the parcel shown below. Provide a check. Show answers on the space provided.
8. List three methods of sheeting an excavation (Sketch each of them)