2.A surveyor is laying out two small concrete slabs for the City of Melbourne, asshown in the figure below. Measuring from a nail and a ribbon set at the intersection of thecenterline of the walking paths (Point 1). What should be the measured distance to layoutthe corners of the two pads (Points 2-9) ifa) The ground is level, and the work is done when the air temperature is 68°Fb) The ground is level, and the work is done when the air temperature is 100°Fc) The ground is level, and the work is done when the air temperature is 10°Flg1720'I10'i120'54NORTH10% 10

Answered: Image /qna-images/answer/de1a3c56-d9d2-4db3-86a5-13060bb2f8bd.jpg

A surveyor is laying out two small concrete slabs for the City of Melbourne, as hown in the figure below. Measuring from a nail and a ribbon set at the intersection of the enterline of the walking paths (Point 1). What should be the measured distance to layout he corners of the two pads (Points 2-9) if a) The ground is level, and the work is done when the air temperature is 68°F b) The ground is level, and the work is done when the air temperature is 100°F c) The ground is level, and the work is done when the air temperature is 10°F

A surveyor is laying out two small concrete slabs for the City of Melbourne, as hown in the figure below. Measuring from a nail and a ribbon set at the intersection of the enterline of the walking paths (Point 1). What should be the measured distance to layout he corners of the two pads (Points 2-9) if a) The ground is level, and the work is done when the air temperature is 68°F b) The ground is level, and the work is done when the air temperature is 100°F c) The ground is level, and the work is done when the air temperature is 10°F

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Define the By Bowle's method ?
Show complete and clear solution also provide illustration thank you. Check your answer twice if it's correct thank you
What is Dimension D? Setback = 0.252, Bend Allowance = 0.345
5. According to Fig. (a), (b), (c), specify what principle or relevant requirement is used on drawings? Draw the dynamic tolerance zone diagram based on specified principle or relevant requirement. +0.03 $20'gas 00.02 (M) |40.01 $20:8 E +0.0 0.01 (a) (b) (c)
#ID = 2
In certain building operation, it was necessary to remove a portion of B hall which was approximately in the shape shown in the sketch. Lower base is see tangle; upper base is a right triangle. AB in parallel to DE; and AC is para a to DG. All face angles at A and at D are right Anglet Altitude of solid is AD - 240 ft.; other dimensions are shown in the sketch. Find the amount of earth removed.
Define Boussinesq’s Method
QUESTION TWO (a) Determine the side widths and areas of the following cross sections:- (i) Fill section 8m Diagram 1 lin3 12.50m Tin3 10 in (ii)' Cut section Lw 2 { in 12 Dịagram 2 in 10 12:25m lin 3
How to determine Z-value? How to determine D-value and TDT?
Given below is the technical description of lot 2081, Cebu Cadastre. LINES 1-2 2-3 3-4 4-1 BEARINGS $32'17' W N 36 25 W N 15'47 W N 73'07 E Find the Area of the lot using a. DMD Method b. DPD Method DISTANCES 22.04 m. 10.00 m. 5.00 m. 19.95 m.
Ex:- Estimate the quantities of the below brick fence & yard with external dimensions 28.68x14.46 m AL Plan 14.46 m-
No. Date 40 5 E= L00 C PA I= L9 X 10 A 2m 4m at C. C. P. the totertion 0.5 Ball Pen 1423