L-shaped part is to be bent in a V-bending operation on a press brake from a flat blank 4.0 in by 1.5 in that is 5/32 in thick. The bend of 90° is to be made in the middle of the 4-in length. (a) Determine the dimensions of the two equal sides that will result after the bend, if the bend radius = 3/16 in. For convenience, these sides should be measured to the beginning of the bend radius. (b) Also, determine the length of the part's neutral axis after the bend?

L-shaped part is to be bent in a V-bending operation on a press brake from a flat blank 4.0 in by 1.5 in that is 5/32 in thick. The bend of 90° is to be made in the middle of the 4-in length. (a) Determine the dimensions of the two equal sides that will result after the bend, if the bend radius = 3/16 in. For convenience, these sides should be measured to the beginning of the bend radius. (b) Also, determine the length of the part's neutral axis after the bend?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please solve it correctly , Don't Use Ai tool. (1) A twist drill bit is used to drill a hole of diameter 2.0 at 4578.1 rpm at a feed rate of 2.5 in/min. Calculate the MRR in in^3/min. Take "pi" = 3.14. Round your answer to the nearest tenth.
.Learning task 3.2 For a No. 7 ball bearing, the New Departure Handbook states that the maximum boreshould be 1.3780 in. and the minimum, 1.3775 in.; for average conditions, the shaftshould have a maximum diameter of 1.3784 in. and a minimum of 1.3779 in.Determine the corresponding tolerances and allowances.
Two gears mounted on shafts have 10 and 15 teeth, respectively. The center distance is 10 inches. The addendum equals the module, and the clearance equals 0.135 times the module. Determine (a) pitch diameters, (b) addendum, (c) dedendum, and (d) root circles. Draw simple circles showing the diameters and the center distance. Complete solution and drawing is required.
I need help with this assignment for drafting I don’t understand it.
Calculate the outer diameter using compound method if the minor diameter is 28mm. angle of taper is 80.The total length of work piece is 120mm and the taper length is 80mm. Also draw the diagram and label the dimensions.
Two parallel shafts are to be connected by spur gearing. The approximate distance between the shafts is 600 mm. If one shaft runs at 120 r.p.m. and the other at 360 r.p.m., find the number of teeth on each wheel, if the module is 8 mm. Also determine the exact distance apart of the shafts.
n the surface roughness standard drawing shown below, the maximum waviness height is: O a. On top of the horizontal line to the right side O b. On top of the open triangle O c. Inside the shape next to the lay direction O d. On top of the horizontal line to the left side
11. What is the radius of a fillet if its chord is 2 inches? What is its area? Page #
Question 5 The hollow steel shaft has an allowable shear stress of [T] MPa. g) Determine the largest torque that can be applied to the shaft. Upload 1.5 m Choose a File 60 mm 40 mm
• Part A Draw the shear diagram for the baam. Folow the sign convention. Fig.m 1) Clok on "add Vertioal line off to add dicoontinulty linec. Then ollok on "add cagment" button to add funotions between the lines. Note 1- You chould not draw an "extra" vertical line at the looation of appled moment. Note 2- Be cure to Indicate the oorreot types of the funotione between the linec, eg. fin your ancwer the type of a funotion Ie "Ilnsar inoressing ciope" for the funotion that actually has linear deoreacing clopa, the ancwer wll be graded as Incorrect Uce the button "ohange cagment" f nsoeccary. 0000 15 kN 10 kN/m 20 kN m 2m 1m No cloments selected v N) 30 20 Im) 20 Add discontinulty ines and seloct segments to add to the canvas Submit dg Aer • Part B Draw the momant diagram for the baam. Follow the sign convention. Cliok on "add vertioal line off to add dicoontinulty linec. Then ollok on "add cagment" button to add funotions between the lines. Note 1- The ourve you chooce from the drop-down…
Angle of twist is . . to shear modulus. a. not related with O b. directly proportional c. inverse proportional d. exponentially proportional
To help facilitate machinig and inspection, what is permitted on both ends of this object?