Please help me with this practice question. Draw Shear/momentdiagram3001bs200 lbsS०० lbs).5' 2'

Answered: Image /qna-images/answer/a1383b97-8de3-4bf2-a447-4b3730a346c3.jpg

Answered: Draw Shear /moment diagram 200 los/fe…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

solve question 7
1) What does the specification "8.8" in the standard designation of a bolt mean? Specify values including units. 2) Name two groups of standards in addition to national, industry-wide standards and where they are valid. 3) Which three options exist for defining dimensional tolerances in a technical drawing?
please can you answer 4B,4C,4D short show working and label each part
We have a rectangular piece. We wish to manufacture a parallel slot along thepiece in a vertical milling machine and 50 cm from the edge. The width of the slot is 40 mm. TheDepth of the slot is 25 mm. For this, several rough cutting steps and aFine cut with a depth of 0.20 mm. The depth for each of the steps ofrough cut is limited to 1.75 mmAditional information:What is the number of blades used for the rough cutting steps?What is the number of blades used for the fine cutting step?
I asked for problems 6 and 7 to be answered, but I did not get a properly structured answered as the example shows on problem number 1. Here is the link to the questions I already had answered, could you please rewrite the answer so its properly answered as the example shows (Problem 1)? https://www.bartleby.com/questions-and-answers/it-vivch-print-reading-for-industry-228-class-date-name-review-activity-112-for-each-local-note-or-c/cadc3f7b-2c2f-4471-842b-5a84bf505857
I need answer within 5 minutes please please with my best wishes
Choose 3 of the most important methods, theorems, principles, or concepts from Statics. Write approximately 3-5 coherent sentences about each IN YOUR OWN WORDS, why they are important, and how they are used. No cutting and pasting except perhaps for an equation or two.
Task 4 Here students need to calculate (a) The cutting speed (b) Turning time (c) Amount of material removed. For a specimen as shown below, if spindle rotates at N = 360 rpm, number of pass = 03, feed rate= 0.2mm/rev, if density of material=7.85× 10-6 Kg/mm³. Appendix Volume for Cylinder = rr?h Volume of frustum= nh (a?+b²+ab)/3 radii 'a' & b' height(Length) 'h'. b-a Taper angle : = tan20 h TDN Cutting speed:V : meters/min 1000 Where: V = Cutting speed in Meter/minute. T= 3.14 D = Diameter of work piece in mm N = rpm Cutting Time Length of the job to be turned NO.of cuts Time to turn mins. Feed/Rev rpm Amount of Material Removed = Original Mass – Machined Mass Original Size of Component 380 mm Machined Component 80 mm 100 mm 120 mm 6 20mm + 25mm + 40mm + 25mm 030mm
Please guide me through the procedure of thoroughly testing individual components.
solve question 6
QUESTION 2 Tool life is the most important factor in the evaluation of machinability. Tool life can be defined as the period of time which the tool cuts effectively and efficiently. A cutting tool should have a long tool life. On the other hand, the cutting speed decreases the tool life due to the abrasive action that occurs between the cutting tool and materials. The increase in cutting speed will decrease the machining time, thus reduce the total machining cost. Justify what actions should be taken to increase the tool life and at the same time shorten the machining time.
a) Name two groups of standards in addition to national, industry-wide standards and where they are valid. b) Which three options exist for defining dimensional tolerances in a technical drawing?

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

Draw Shear /moment diagram 200 los/fe 1bs, 50olbs 300bs A I' 1.5' 2'