Knowing that the tension in cable AB is 1425 N, determine the components of the force exerted on the plate at B. 360 mm 920 mm lo B D 600 mm C 900 mm
Q: 1. A mass is supported by the cable system shown below. If the tension in cable A is 14 kN, find the…
A: Tension in cable A: TA = 14 kN = 14000 N Cable attached to mass "m" composed of aluminium alloy:…
Q: 1.10 Link BD consists of a single bar 1 in. wide and in. thick. Knowing that each pin has a -in.…
A:
Q: A force stretches a wire by 1.4 mm.
A:
Q: Determine the magnitude of the force (in N) of the y-component of the internal pin at D.
A: To solve this question we will use the concept of rotational equilibrium. The equilibrium in which…
Q: Calculate the shear modulus (G) for a cylindrical steel specimen. Assuming the elastic modulus is…
A:
Q: If the beam attached to a hinge is 4 meters long and weighs 600 Newtons, and the sign weighs 400…
A:
Q: 5. A wire made of the same material (Y= 12X100Pa) is cut into two parts, we label it as wire I and…
A: The wire is cut into two pieces. Piece 1 : Length L1 = L , diameter d1= d Piece 2 : length L2 =…
Q: Determine the largest weight W that can be supported by two wires shown in Fig. The stress in either…
A: Maximum weight supported by the given system of wires is equal to the sum of vertical components of…
Q: Two wires of equal cross- section one made up of aluminium and other of brass are joined end to end.…
A: To find- Ratio of length of two wires L1L2=? Given- lAL=lbrass=l,MAL=Mbrass=MrAL=rbrass=rYAL=7×1010…
Q: : Two wires of equal cross-section one made up of aluminium and other of brass are joined end to…
A: We need to find- Ratio of lengths of two wires LAlLbrass=? The data given as-…
Q: A 557-N force is applied to stretch a cable, 66-m long and has a cross-sectional area of 2.8 mm^2.…
A: Given that-Force, F=557 NLength, L=66marea, A=2.8 mm2Y=1×1011 N/m2
Q: 3. Using the Method of Sections determine the load in members BD, CD, and CE.
A:
Q: A very fine fabric 0.020 mm in diameter can support a 28 g object. How does the stress in the fabric…
A:
Q: A bar of 25 mm diameter is subjected to a tensile load of 50 KN. Calculate the extension on a 300…
A: From the question, we can identify the following values:Diameter of the bar (d) = 25 mmTensile load…
Q: What is the load should be placed on a wire of diameter 2 mm so that the permitted strain does not…
A: Given data: Strain =1/1000=10-3. Modulus of elasticity Y=35×1010 N/m2. Diameter of the wire d=2mm
Q: You apply a force of magnitude F1 to one end of a wire and another force F in the opposite direction…
A: Newton's second law of motion relates the net force acting on the object to the acceleration…
Q: Determine the force in member AE of the loaded truss. The force is positive if in tension, negative…
A: Solution:-Given that
Q: What is the stress for a wire of 5 m long so that the strain is 2% of 0.2? The cross-sectional area…
A:
Q: Assume Young's modulus for bone is 1.50 x 1010 N/m2. The bone breaks if stress greater than o= 79104…
A: maximum stress= sigma= 79104 N/m2
Q: The radius of a copper 4 mm. What force is required to stretch the wire by 20% of its length,…
A: To find-Force required (F)=?Given-Elastic limit is not exceeded.Radius of copper wire (r)=4 mm…
Q: how can I derive formula to find the original volume, given the bulk modulus, change in volume and…
A: The bulk modulus is defined as the ratio of the volumetric stress to the volumetric strain.
Q: Load (N) Length (mm) 40 100 40.2 200 40.4 250 41 300 42 350 43 400 45 450 48 420 51 40
A:
Q: The dimensions of the Tensile Stress is Select one: O a. MLT-1 O b. ML2T-2 O c. MLT-2 O d. ML-1T-2 O…
A:
Q: - A rigid member CBD is supported by a flexible cable AB as shown below. If a force applied to the…
A: Take point C as origin and vertical as y axis. Initial coordinate of point B =0,300 Initial…
Q: A wire made of the same material (Y= 12X1010Pa) is cut into two parts, we label it as wire I and…
A: Given data: The Young's Modulus of the wire, Y=12×1010 Pa. Wire I is 3 times as long and half the…
Q: A 557-N force is applied to stretch a cable, 66-m long and has a cross-sectional area of 2.8 mm^2.…
A: Given that-Force, F=557 NLength, L=66marea, A=2.8 mm2Y=1×1011 N/m2We know that,Hook's law FA=Y×∆LL…
Q: A material is made in circular rod form of diameter 0.6 cm and 10 cm long . It is fixed on the…
A: Dear student The strain is defined as Change in length per unit original Length. Strain = ∆L/L
Q: The deepest point in any ocean is in the Mariana Trench, which is about 11 km deep, in the Pacific.…
A:
Q: Block A is held in equilibrium when force F = 140 lbf is applied. Each cable is made out of 5-0s…
A:
Q: 75 kN Composite A-36 steel bar shown made from two segments AB and BD. Area A= 600 mm² and App=1200…
A: Write the given values of this problem. AAB=600 mm2ABD=1200 mm2
Q: Find the internal load of each section of the bar due to the loading shown. Alsofind the maximum…
A: Solution:-Given thatthickness of the bar (t)=0.5 in
Q: A 1.5-m-long, 1.0-mm-diameter steel string is pulled by a 3.1 x 103 N tension force. By how much is…
A:
Q: The Force of resistance per unit area offered by a body against deformation is the stress. Is this…
A: The Force of resistance per unit area offered by a body against deformation is the stress. YES this…
Q: A force stretches a wire by 1.0 mm.a. A second wire of the same material has the same cross section…
A: Young's modulus is the mechanical property of a material which measures the stiffness of the…
Q: Determine the normal force N inside each bar Sa function of the external force P 1.5 m 2 m
A: Free body diagram:
Step by step
Solved in 2 steps with 2 images
