Knowing that the tension i n cable AC is TAC = 401 N, determine the  y-component of TAC . Round off only on the final answer expressed in 3 DECIMALS and also indicate the units.

Q: The structure below supports a 4-kN force. It is constrained by the cords BC and BD and by a…

A:

Q: The force system shown is composed of three forces: A = 35.75 kN, B = 41.83 kN. If β = 56.36°, what…

A:

Q: Solve for the forces in wires a, b, c and d. C 45° d a 60 150 lb

A: Given: Load (P)=150lb

Q: – 24 in.- D 10 in. В C - y --

A:

Q: Shown below is a toggle clamp that exerts only a vertical clamping force on the wood block at A.…

A: The force is The length of handle is

Q: Q1\ ABD consists Isosceles triangle. The AB and AD help support pole AC. Known that the tension in…

A:

Q: height of tower = SD m use 3. Compute for the cable forces acting on the tower shown. D |-60 m – 60…

A: Given Data The height of the tower is H=50 m. First, we have to draw the free-body diagram of the…

Q: 200 400 200 N m E 200 F Dimensions in mm Neglecting the weights of the members, determine the…

A: GIVEN DATA A FRAME GIVEN WE HAVE TO FIND REACTION AT F IN N

Q: Q1: The 750 N tension force in cable AB is required to prevent the CA bar from rotating clockwise.…

A: Given Data: The tension in the cable AB is T = 750 N. The configuration diagram can be drawn as,…

Q: Situation 3. The rope CE exerts a 500-N force T on the hinged door. (a) Express T in terms of…

A:

Q: iv) Examine the solution from the calculation if this magnitude is obtained based on the above FBD…

A:

Q: Determine the force in each member of the loaded truss. Discuss the effects of varying the angle of…

A: Given data as per the question The load applied at point A =440 lb

Q: L Oetermine the value g the Reaction A 2. Determine the valueg the Reactions L 9, the value The…

A:

Q: The 250-N block rests upon a level plane for which fk = 0.2. It is pulled by force P = 100N inclined…

A: Given DataW=250NP=100NV=17.862 m/s {As velocity is not given in question we have to take the…

Q: Determine the magnitude of the component of the tension force (in kN BD along the designated x-axis.…

A:

Q: A machine component is subjected to the forces and couples shown. The component is to be held in…

A:

Q: 1. (1 point) If F is in the -y direction and has a magnitude of 4kN, what is the force in bar A A.…

A: GivenF=4kN

Q: F = 500 lb Determine the components ofF, and F, in x-y and x’-y’ systems 25 450 30 F2 = 750 lb

A:

Q: Cables AB, BC and AD support a 10 kips load as shown. Determine; a) The magnitude of the tensions in…

A:

Q: possible methods. В A 4m 8m 4m 4m 600KN

A: To find magnitude of vertical and horizontal forces on each joint

Q: 8 kN/m 35° OE D C d d d

A:

Q: The 47-lb square plate shown is supported by three vertical wires. Determine the tension in wire A…

A: Given weight = 47 lb let Ta,Tb,Tc be the tension in the wire a,b,c respectively Free body diagram

Q: You must have to include the diagram. Don't make any mistakes while solving.

A:

Q: y mm mm |B A

A:

Q: Situation 5. Determine the forces in cables AC and AB needed to hold the 20-kg ball D in…

A: GivenF=300Nm=20kgd=1m

Q: Determine the tensions in the belt on pulley B assuming the shaft is running at a constant speed.…

A: Given:T2 = 0.15 T1dA = 8 indB = 7 in To find: T1 and T2

Q: Determine the magnitude of the resultan force FAC = 400 N 2m L im A Z 0.75 m A 250 N 2 m 3 m B y

A: The magnitude of the force, The magnitude of the force,

Q: The frame shown supports a crate that weighs W = 250 lb. Knowing that L = 1.1 ft, determine the…

A: According to the given dataW=250 lb L=1.1 ftr=0.4 ftWe need to findInternal force N,V and M at…

Q: Determine the force (N) in link AB if P = 23.7 kNand d = 0.44. Round off only on the final answer…

A: When there is any relative motion between any two surfaces, there is a force that opposes the motion…

Q: A lifeboat hangs from two ship’s davits, as shown in the figure. A pin of diameter d = 0.8 in.…

A: Draw the free-body diagram of the pulley. Here, F is the shear force in the pin. Resolve the…