Solve for the forces in wires a, b, c and d. C 45° d a 60 150 lb

Q: 4. Replace the coplanar force system that acts on the casting with an equivalent force-couple…

A: 4) From the triangle, sinθ=35cosθ=45

Q: The 60° V-belt of a machine is pass around the pulley A of a motor and over a pulley B as shown in…

A:

Q: Table 2 Exponential multiplier (power of ten) Prefix Micro Nano Mega Pico Deci

A: Prefix                      exponential multiplier Micro                           -6 Nano…

Q: Which material is considered as ductile and which one is considered as brittle? Explain. What is the…

A: Given: To determine:  which material is brittle and which one brittle material

Q: A semi-circular vertical plate is partially submerged in the water as shown in the figure. What is…

A: Find the force on the plate due to hydrostatic pressure.

Q: 2. A spherical object has a radius of 0.45 cm. The density of water is 1000 kg/m3. If the block is…

A: Given data as per question The radius of object =0.45 cm Density oof water =1000 kg/m3

Q: For the control system shown in fig-2, a) Find the values of K and K₁, such that the closed loop…

A: Given:To find:

Q: A wooden Cylinder of diameter 'd' and length '2d' floats in water with its fixes vertical, Is the…

A:

Q: Water (Cp = 4.183 kJ/kg-k) flowing at a rate of 0.8 kg/s enters a counter current heat exchanger at…

A:

Q: can you answer 1B

A:

Q: You are asked to explore the operating principles and efficiencies of hydraulic machines. You have a…

A: As per the guideline, I am solving on part A and B. For rest parts, re-post in a separate post. a)…

Q: The shear stress at a point in oil having specific gravity 0.98 is 0.25 N/m? and velocity

A:

Q: A fireworks show is choreographed to have two shells cross paths at a height of 125 feet and explode…

A:

Q: The hydraulic cylinder CF, which partially controls the position of rod DE, has been locked in the…

A: GivenThickness of member BD=15mmP=2knθ=75° FBD of BCD

Q: Question The bronze bar 3 m long with a cross-sectional area of 430 mm2 is placed between two rigid…

A:

Q: Determine the force in members GH, GB, and BC, and state whether the members are in tension or…

A:

Q: The tongs are used to lift the 150-kg crate, whose center of mass is at G. Suppose that 0 = 31 °.…

A: Given, Mass of crate = m = 150 kg Weight of crate = W = mg = (150) (9.81) = 1471.5 N Angle θ = 31o…

Q: 5. Calculate the theoretical air/fuel ratio by mass and the percentage composition of the products…

A: According to terms and conditions of bartleby we can only provide 1st solutions (Q5). Thank you !

Q: 13mm diameter rod is to be reduced to 11mm diameter by drawing in a single pass at a speed of…

A:

Q: A differential manometer is attached to pipe (p=10cm) which deposites a volume of 5 drums an hour ,…

A: given; specific density of oil(S)=0.90density of mercury(ρHg)=13600kg/m3diameter of pipe(d1)=10cm…

Q: Q.4 Determine radiation heat loss from a steel tube of outside diameter 60 mm and 5m long at a…

A: Data given-  D = 60 mm = 0.06 m  L = 5 m  T1 = 327+273 = 600 K  T2 = 25 +273 = 298 K  ε1 = 0.8  ε2 =…

Q: If w-15 kN/m, determine the following: a. Maximum tensile stress in the beam. b. Maximum compressive…

A: Given data:-Length of beam, L=3m=3000mmMaximum intensity of UVL, ω=15kN/mdepth of cross-section,…

Q: Determine the force in member BD of the truss shown. | 1 kip | 4 kips |1 kip B 6.4 ft D E 2.4 kips…

A:

Q: Pin-connected rigid bars AB, BC, and CD are initially held in the positions shown by taut wires (1)…

A:

Q: The solid 1.35-in.-diameter rod is subjected to a uniform axial distributed loading along its length…

A:

Q: ) Find the moment of inertia of the cross section to the right about the x and y axes shown. In…

A:

Q: A body weighs 4.25 N in air and 3.5 N when submerged in water. Given that water has a density of…

A: Given data  weight of the body in the air (W) = 4.25 N weight of the body in the water (Ww) = 3.5 N…

Q: 4. A water bomber für fighting fires is flying horizontally at om altitude of 1.00 km, as shown. How…

A:

Q: The following Brayton cycle is assumed to operate on air with an inlet pressure of 100 kPa, an inlet…

A:

Q: PROBLEM 1: Vectors What is the magnitude and direction with respect to the positive x-axis of the…

A:

Q: (c) You can paddle your cycle maximum three times per second. If the diameter of driver pa wheel is…

A: RPM of paddle wheel, N1 = 3*60 rpm =180 rpm diameter of the paddle wheel, D1 =20 cm Diameter of gear…

Q: 22. The size of ball and roller bearing can be identified by. a. rolling member size b. inner race…

A: 22. The size of ball and roller bearing can be identified by rolling member size. hence option {a}…

Q: 1. A gate as shown in the figure is 1.6m wide and 1 m high. Its top is supported by a hinge and a…

A:

Q: Determine The çorce in CB member of the truss, and state iç the members are in tension or…

A:

Q: A capillary -tube viscometer is being selected to measure viscosity of a liquid food. The maximum…

A: Solution to Q1 as per our company policy. (e)

Q: Please help me answer this question.

A: given  design the given beam

Q: e water flow rate through the vertical bend shown in the figure is 2.83 m³/s. Cal agnitude,…

A:

Q: (e) Caleulate the angular velocity of the gas mixture using padelle wheel model eylinder engine by…

A: Data given- Swirl ratio = 1.1