Part 1 The Free-Body diagram for bar ABC is shown. Note that bar BD is a two-force member. Solve for the force BD. A, Answer: BD = i B 57° BD N 790 N

Q: Problem 8) In Figure 1.8 below, the man on the left pulls a rope with a force which has a magnitude…

A:

Q: If the resultant of the loads shown passes through point B, determine the equivalent force-couple…

A:

Q: can you help me to do the position analysis of this mechanism and find the mathemetical expressions…

A: Given:To find:Draw the position analysis and find the angle values.

Q: Q1: Find the torque of the force 800 N in figure (1) about point 0.

A:

Q: Homework - 2 Q1: Find the torque of the force 800 N in figure (1) about point 0.

A: we will split the force in two parts horizontal and vertical and then find their respective  moments

Q: Given: F₂ = F₁ = 800 N 450 N Fix F₁ cosp F2x =[ F3x 400 N -270 N F3 ΣFx = ΣFy F3y Page 1 FlyF₁ sind…

A:

Q: Problem: In the probiem below, distances are specified from left to right. The distance between…

A: GIVEN : Value of P : To Determine :

Q: A position vector from point B to the line of action of a force vector F is given as: "BF = {-10j +…

A: rBF=-10j+20k m

Q: Assume an origin at the point where the rope is tied to the boat. Assume a y-axis perpendicular to…

A:

Q: ▸ An incompressible Newtonian fluid flows between two parallel plates (distance b). The bottom plate…

A:

Q: If the force applied to the wheel is doubled in size, Then the torque produced in the wheel would be…

A: correct Answer:   True

Q: Inatwo-dimensional tug-of-war, Alex, Betty, and Charles pull harizantally on an automohile tire at…

A:

Q: Find the total force A

A: Given Data:   To Find: Magnitude of A.

Q: 2-22. Determine the design angle (0 ≤ ≤ 90°) between members AB and AC so that the 400-lb horizontal…

A:

Q: A race car is turning (cornering) on a flat road, as shown in Figure Q1-1. The speed of the car is…

A: Given Data- 1. Speed of car  v=300km/h 2. Turning radius  r =260m 3. mass          m   =890Kg (57%…

Q: Replace these 3 forces with a single equivalent force R. T2 T3 Show R on a sketch of the eye bolt.

A: Given Data: The magnitude of the first force is, T1=110 lbs. The magnitude of the second force is,…

Q: The force which is acting on a body at right angles to its surface is called O In-direct force…

A: In direct force - A force is acting without making contact with another body. Direct force - when…

Q: 4/113 Determine the components of all forces acting on each member of the loaded frame. A M C R M…

A:

Q: Find the couple moments acting on the gear. F = 350 N 40° 0.5 m 40° F = 350 N (a)

A: In the given figure the vertical component of side 350 N force  and horizontal component of lower…

Q: termine the force at A and B the Figure 6N

A:

Q: Determine the length of stroke of a slider E when the crank AC rotates by 30 degrees in counter-…

A: Given data,AC=35cmAB=70cmCD=45cmBD=45cmDE=40cm

Q: Q1: Find the torque of the force 800 N in figure (1) about point 0.

A:

Q: For the beam shown determine the slope and deflection equations for 0<x< L using the…

A:

Q: For the stress states above determine the required yield strength of the material based on the…

A:

Q: 2.5" 30.375" s 18.75" 4.25 26" 2.5" Espring FBY Fax 7 Analyze the forces acting on the clutch fork…

A: The force analysis can be done by using the equilibrium equation on anybody. The Shaft has lots of…

Q: 4m 10m F 6 m, 8 m Zom- 8m

A: Find the moment about origin (O) Given data :-  F = 300 N

Q: Jacobian. The velocity of the end-effector is given in terms of the joint velocity vector by Find…

A: Given : To find : Jacobian matrix

Q: grees sideways. AB-20, BC-25, CD-30, 8D-50, CF-4Scm. Draw in appropriate scale

A:

Q: Problem 3: Note: Make sure to draw all diagrams. All Units must be included. Determine the magnitude…

A:

Q: In the drawing, arm A is being driven back and forth in the direction of the arrows. It is connected…

A: Solution: Given Data: Screw B is lowered towards the end of arm A.   To Find: What happens to the…

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.